FI KÄYTTÖOHJE
20
RAPTOR LED-VALONAUHA: VAROITUKSET!
1. Älä koskaan kytke LED-valonauhaa virtalähteeseen, kun se on pakattuna tai kierrettynä kelalle.
2. Älä taita valonauhaa tai roikuta vaakasuorassa tukematta sitä keskeltä, äläkä taivuta lyhyttä
sivua pitkin.
Taittosäteen on oltava vähintään 8 cm. Älä taivuta LED-nauhaa asennuksen aikana.
3. Älä käytä LED-valonauhaa, kun sen on peitettynä tai laskettuna alustalle.
4. Älä avaa tai leikkaa LED-valonauhaa.
5. Tätä LED-valonauhaa ei saa käyttää, ennen kuin kaikki tiivisteet ja liittimet ovat paikoillaan.
6. Älä liitä tätä LED-valonauhaa minkään muun valmistajan tuotteisiin.
7. Liitoksissa on käytettävä ainoastaan mukana tulevia RAPTOR-liittimiä. Kaikki avoimet päät on
sinetöitävä tulpilla ennen käyttöä.
8. Älä peitä tätä tuotetta - se voi aiheuttaa ylikuumentumista, sulamisen tai tulipalon.
9. Älä upota LED-valonauhaa nesteisiin tai käytä sitä veden tai muiden nesteiden läheisyydessä.
10. Älä vie johtoa seinien, kattojen, ovien, ikkunoiden tai muiden rakenteiden läpi.
RAPTOR LED ROPE LIGHT: WARNINGS!
1. Never connect the Rope Light to a power supply while it is packaged or wound
onto a reel!
2. Do not twist, hang vertically, unsupported in the middle or bend along short
side:
Minimum bending diameter = 8cm. Do not fold the LED strip during installation
3. Do not use the rope light when covered or recessed into a surface.
4. Do not open or cut the rope light.
5. This rope light must not be used without all gaskets / connectors being in
place.
6. Do not connect this rope light to another manufacturer’s product.
7. Connections shall be made only using the supplied RAPTOR connectors. Any
open ends must be sealed-off before use with end-caps.
8. Do not cover this product - may cause overheating, melting or fire.
9. Do not submerge the Rope Light in liquids or use the product in the vicinity of
standing water or other liquids.
10. Do not route the cord through walls, ceilings, doors, windows, or any similar
RAPTOR LED ROPE LIGHT: WARNINGS!
1. Never connect the Rope Light to a power supply while it is packaged or wound
onto a reel!
2. Do not twist, hang vertically, unsupported in the middle or bend along short
side:
Minimum bending diameter = 8cm. Do not fold the LED strip during installation
3. Do not use the rope light when covered or recessed into a surface.
4. Do not open or cut the rope light.
5. This rope light must not be used without all gaskets / connectors being in
place.
6. Do not connect this rope light to another manufacturer’s product.
7. Connections shall be made only using the supplied RAPTOR connectors. Any
open ends must be sealed-off before use with end-caps.
8. Do not cover this product - may cause overheating, melting or fire.
9. Do not submerge the Rope Light in liquids or use the product in the vicinity of
standing water or other liquids.
10. Do not route the cord through walls, ceilings, doors, windows, or any similar
RAPTOR LED ROPE LIGHT: WARNINGS!
1. Never connect the Rope Light to a power supply while it is packaged or wound
onto a reel!
2. Do not twist, hang vertically, unsupported in the middle or bend along short
side:
Minimum bending diameter = 8cm. Do not fold the LED strip during installation
3. Do not use the rope light when covered or recessed into a surface.
4. Do not open or cut the rope light.
5. This rope light must not be used without all gaskets / connectors being in
place.
6. Do not connect this rope light to another manufacturer’s product.
7. Connections shall be made only using the supplied RAPTOR connectors. Any
open ends must be sealed-off before use with end-caps.
8. Do not cover this product - may cause overheating, melting or fire.
9. Do not submerge the Rope Light in liquids or use the product in the vicinity of
standing water or other liquids.
10. Do not route the cord through walls, ceilings, doors, windows, or any similar
