Rapsody RSH-250 Additional Information Download | Manualshive

Page: 14 / 15

background image

USB O.T.G. firmware Upgrade

14

4. Decompose downloaded O.T.G. firmware file and
execute [Enduser.exe].

5. Push the [Download] button to start upgrade.

Caution:

NEVER switch off RSH-250 or disconnect USB cable during O.T.G. firmware upgrade, which may
result in fatal damage to the product.
Download firmware files on http://www.bull-it.ch.

6. Wait for firmware upgrade to be completed. NEVER turn
off the power or disconnect USB cable.

7. The following screen appears when the firmware
upgrade is completed successfully. Then, RSH-250 starts
automatically and detected as a portable storage device
by PC.

8. Click [OK] and then [Quit] to exit the upgrade program.

«
...
12
13
14
15
»

Summary of Contents for RSH-250
















Reviews:

No comments

Related manuals for RSH-250

Brand: Nakamichi Pages: 36

Brand: Manhattan Pages: 2

Brand: Sencore Pages: 112

Brand: Radyne ComStream Pages: 156

Brand: Transition Networks Pages: 2

Brand: NAIM Pages: 28

Mediagate MG-450HD

Brand: AL Tech Pages: 100

Brand: BenQ Pages: 64

Brand: B&B Electronics Pages: 2

Giga-McBasic II

Brand: B&B Pages: 2

Sync Converter/Stabilizer SCS 300

Brand: Extron electronics Pages: 1

Al-Mu'allim AM-RD2

Brand: PLAYNETICS Pages: 21

Brand: TA Pages: 32

Brand: GALCO Pages: 8

Brand: CEL-MAR Pages: 28

basic-line DCC 1-00

Brand: axing Pages: 4

Brand: Linear Pages: 3

Brand: Casti Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands