background image

12

Important Safety Instructions

• Before using this device, read these operating instructions carefully and keep this user manual for future
reference.

• Before using the product, check the desk and power cables for any visible signs of damage. If you notice
cuts or deep scratches, do not turn on the device.

• Before connecting the product to the power supply, make sure that the power supply voltage is
compatible with the parameters of the product.

• Before using it, make sure that the length of the power cable allows you to connect the desk to the power
supply.

• The height-adjustable desk contains electronic circuits and should only be used in dry environments. Do
not use outdoors or in very dusty environments. Keep away from heat sources and any corrosive materials.

• Keep all electrical components away from liquids. Never touch or handle the desk, power supply, the
control box, the panel control or any other cable with wet hands.

• Clean the product only with a clean, dry, soft cloth or cloth. Disconnect from the power supply before
moving or cleaning electrical components.

• Do not disassemble the columns, control box and control panel. These actions are considered damage
caused by the user.

• This product contains small parts. Make sure they are out of the reach of children. Do not allow children
to play with the device. Packing materials must not be used as toys.

• Do not lay or sit on the worktop. This product is not for lifting people.

• Do not exceed the maximum permissible load weight.

• This product can be used in a 10% cycle (2 minutes of operation, followed by 18 minutes pause).

• The manufacturer cannot be held liable or responsabile for any damage or injuries resulting from
improper use of the vacuum cleaner, in other words, non-compliance with these safety instructions and
warnings.

Summary of Contents for Boost Plus Single Sided Desk Workstation



















Reviews: