background image

11

Visit us at 

www.rapala.ca

Operator's Manual

RAPALA

®

 

Power Ice Auger

ORDERING REPAIR PARtS

parts may be obtained from the store where your auger was purchased or 

direct from the factory. To order from the factory, call, e-mail, or order online 

at www.rapala.ca:

Normark Inc, 

1350 Murray Avenue 

Oshawa ON, Canada L1J 6Z9 

E-mail: [email protected]        tel: (905) 571-3001

Please include the part numbers, part description, quantity, model number 

and serial number.

tROUBLESHOOtING:

PROBLEM

POSSIBLE CAUSE

REMEDy/ACtION

Engine will not start

1. power switch off

1. Flip switch to ON position

2. Spark plug wire disconnected

2. Connect spark plug wire to spark plug

3. Out of fuel

3. Refuel

4. Spark plug wet, faulty or  

improperly gapped

4. Clean, replace or gap spark plug

Engine runs rough, floods during 

operation

1. Dirty air filter

1. Clean or replace air filter

2. Choke partially engaged

2. Turn off choke

3. Carburetor out of adjustment

3. Call factory

Engine is hard to start

1. Stale fuel

1. Drain old fuel and replace with fresh. Always 

use gas stabilizer

2. Spark plug wire loose

2. Make sure spark wire is securely attached to  

     spark plug

3. Dirty carburetor

3. Clean carburetor, use gas stabilizer, new gas can

Engine misses or lacks power

1. Clogged fuel filter

1. Remove and clean or replace

2. Clogged air filter

2. Remove and clean or replace

Auger turns at idle

1. Idle speed too high

1. Adjust idle speed lower

2. Broken clutch spring

2. Replace both springs

Auger turns, but has no power

1. Choke on

1. Turn off choke after engine is running

2. Carburetor out of adjustment

2. Call factory

3. Broken transmission

3. Call factory

4. Worn clutch shoes

4. Replace clutch shoes and springs

Auger jumps on ice

1. Blades damaged or sharpened  

incorrectly

1. Replace with new blades

Auger cuts slowly

1. Dull blades

1. Buy new blades

2. Damaged point

2. File point, or replace point

Contact service provider if above remedies fail, or visit our website at www.rapala.ca for additional frequently asked 

 

questions.

Summary of Contents for BLACK ICE















Reviews: