Visit us at
www.rapala.ca
14
Operator's Manual
RAPALA
®
Power Ice Auger
(1) Designed, built and equipped so as to conform with all
applicable regulations adopted by the EpA pursuant to their
respective authority, and
(2) Free from defects in materials and workmanship which, at
any time during the ECS Warranty period, may cause a warranted
emissions-related part to fail to be identical in all material
respects to the part as described in the engine manufacturer’s
application for certification.
The ECS Warranty only pertains to emissions-related parts on
your engine, as follows:
(1) Any warranted, emissions-related parts that are not
scheduled for replacement as required maintenance in the
Maintenance Schedule (located in the section of the Manual(s)
pertaining to maintenance) shall be warranted for the ECS
Warranty period. If any such part fails during the ECS Warranty
period, it shall be repaired or replaced by Ardisam according to
Subsection (4) below. Any such part repaired or replaced under
the ECS Warranty shall be warranted for the remainder of the
ECS Warranty period.
(2) Any warranted, emissions-related part that is scheduled
only for regular inspection as specified in the Maintenance
Schedule (located in the section of the Manual(s) pertaining to
maintenance) shall be warranted for the ECS Warranty period. A
statement in such written instructions to the effect of “repair or
replace as necessary” shall not reduce the ECS Warranty period.
Any such part repaired or replaced under the ECS Warranty shall
be warranted for the remainder of the ECS Warranty period.
(3) Any warranted, emissions-related part that is scheduled
for replacement as required maintenance in the Maintenance
Schedule (located in the section of the Manual(s) pertaining to
maintenance) shall be warranted for the period of time prior to
the first scheduled replacement point for that part. If the part
fails prior to the first scheduled replacement, the part shall be
repaired or replaced by Ardisam according to Subsection (4)
below. Any such emissions-related part repaired or replaced
under the ECS Warranty shall be warranted for the remainder
of the ECS Warranty period prior to the first scheduled replace-
ment point for such emissions-related part.
(4) Repair or replacement of any warranted, emissions-related
part under this ECS Warranty shall be performed at no charge
to the owner at a Ardisam Authorized Warranty Service Facility.
(5) When the engine is inspected by a Ardisam Authorized
Warranty Service Facility, the owner shall not be held respon-
sible for diagnostic costs if the repair is deemed warrantable.
(6) Ardisam shall be liable for damages to other original engine
components or approved modifications proximately caused by
a failure under warranty of any emission-related part covered
by the ECS Warranty.
(7) Throughout the ECS Warranty period, Ardisam shall maintain
a supply of warranted emission-related parts sufficient to meet
the expected demand for such emission-related parts.
(8) Any Ardisam authorized and approved emission-related
replacement part may be used in the performance of any ECS
Warranty maintenance or repairs and will be provided with-
out charge to the purchaser/owner. Such use shall not reduce
Ardisam’s ECS Warranty obligations.
(9) Unapproved, add-on, modified, counterfeit and/or “grey
market” parts may not be used to modify or repair a Ardisam
engine. Such use voids this ECS Warranty and shall be sufficient
grounds for disallowing an ECS Warranty claim. Ardisam shall
not be held liable hereunder for failures of any warranted parts
of a Ardisam engine caused by the use of such an unapproved,
add-on, modified, counterfeit and/or “grey market” part.
EMISSION-RELAtED PARtS INCLUDE tHE
fOLLOWING (If EQUIPPED):
(1) Fuel Metering System
(i) Carburetor and internal parts (and/or pressure
regulator or fuel injection system).
(ii) Air/fuel ratio feedback and control system.
(iii) Cold start enrichment system.
(iv) Fuel Tank.
(2) Air Induction System
(i) Controlled hot air intake system.
(ii) Intake manifold.
(iii) Air filter.
(3) Ignition System
(i) Spark plugs.
(ii) Magneto or electronic ignition system.
(iii) Spark advance/retard system.
(4) Exhaust Gas Recirculation (EGR) System
(i) EGR valve body, and carburetor spacer if applicable.
(ii) EGR rate feedback and control system.
(5) Air Injection System
(i) Air pump or pulse valve.
(ii) Valves affecting distribution of flow.
(iii) Distribution manifold.
(6) Catalyst or Thermal Reactor System
(i) Catalytic converter.
(ii) Thermal reactor.
(iii) Exhaust manifold.
(7) particulate Controls
(i) Traps, filters, precipitators, and any other device
used to capture particulate emissions.
(8) Miscellaneous Items Used in Above Systems
(i) Electronic controls.
(ii) Vacuum, temperature, and time sensitive valves
and switches.
(iii) Hoses, belts, connectors, and assemblies.
