background image

 

EcoPro 

Range Road Enterprises Ltd 
Box 944 
Eckville AB T0M 0X0 
www.range-road.ca

 

 

Page 4 

       
     
                          Never wear loose clothing, when operating the firewood processor. 
 
 
                                      Only operate the firewood processor in daylight. 
 
 
                                    Wear safety glasses to avoid eye injury as pieces of log may fly out while splitting. 
 
                                   
                                      High  pressure  hydraulic  fluid  can  inject  under  skin  resulting  in  serious  injury  including 

amputation. 

 
 
                                      Make sure all fittings are tight before applying pressure. Relieve system   

pressure before servicing. 

 
                                      Do not check for leaks with hand. Instead, use a piece of cardboard to check for leaks. 
 
   
                                      If skin injection happens, seek immediate “Medical Assistance”. 
   
 
                                      Serious injury or death can occur if towing safety rules are not followed. 
 
 
                                      Review towing safety warnings in your towing vehicle manual. 
 
 
                                      Drive safely. Be aware of the added length of the firewood processor. 
 
 
                                      Never ride or transport cargo on the firewood processor. 
 
 
                                      Drive the vehicle with the firewood processor securely attached. 
 
                                      Choose a level surface to operate the firewood processor. 
                                      Block the firewood processor wheels to prevent unintended movement. 
 
 
 

 
 

Summary of Contents for EcoPro Series



















Reviews: