background image

 

EcoPro 

Range Road Enterprises Ltd 
Box 944 
Eckville AB T0M 0X0 
www.range-road.ca

 

 

Page 5 

Never  tow  or  operate  this  processor  while  under  the  influence  of  alcohol,  drugs,  or 
medication.   

 

Risk of fire and explosion.   

Hot exhaust fumes from engine can cause fire. Gasoline is highly flammable and explosive.   
You can be burned or seriously injured when handling fuel.   

   
                                      Position muffler at least 213 cm (7 feet) from combustible objects. 
 
 

Before adding fuel, stop the engine and keep heat, sparks, and flame away. Do not add fuel 
when engine is running or still hot. Do not smoke near the engine while fueling.   
 
Pay attention to the conveyor height, if the conveyor is too high or split wood lengths to 
long the wood will jam into the conveyor belt instead and possibly tear it, conveyor can be at 
a higher angle with shorter lengths of wood. 
 
Do not pump fuel directly into engine at gas station. Static charge can build and ignite fuel. 
Use  a  safety  approved  fuel  container  to  transfer  gas  to  the  engine.  Wipe  up  fuel  spills 
immediately. 
 

Only store and handle fuel outdoors. Gasoline vapors can ignite if they   
collect inside an enclosure. Explosion may result. 

   

Do not change or add to exhaust system. Fire may result.   

 
 

Do not change or add fuel tanks or fuel lines. Fire may result.   

 
 

Before each use, check fuel tank and fuel lines for leaks. Any fuel leak is a fire hazard. Fix 
any fuel leaks before starting engine.   

 

During transportation take precautions to make sure machine will not tip over and cause a 
fuel leak fire hazard.   

 

Poisonous fumes from engine can kill you. Do not operate indoors even if ventilated.   
For outdoor use only.   

 

Do not touch the muffler as you may get burned.   

 
 

 
 

Note: Any modification to Processor will void all warranty 

Summary of Contents for EcoPro Series



















Reviews: