background image

 

R&G Racing 

Unit 1, Shelley’s Lane, East Worldham, Alton, Hampshire, GU34 3AQ 

Tel: +44 (0)1420 89007  Fax: +44 (0)1420 87301  

www.rg-racing.com

  Email

[email protected]

 

 

- 4 -

 

 

Prendre la base plate usinée (Photo gauche du haut) et placez là à la base de la 

béquille par dessous pour qu’elle s’aligne avec la plaque.

 

 

Appliquer un peu de colle Loctite Bleu 242 sur l’extrémité du filetage de chaq

ue vis. 

 

Utiliser les 3 boulons pour fixer la position, en veillant à ce que le bord intérieur de la 

base plate s’emboîte sur le haut de la base de la béqui

lle. 

 

Serrer tous les boulons de façon égale et vérifier que la béquille ne touche pas la 
chaîne en position relevée. 

 

Si l’installation se fait sur une béquille ancienne assez usée, la bande de 

rembourrage doit être placée dans la base plate afin d'assurer un ajustement plus 
serré. 

  

 

ISSUE 1   20/06/2014   (NSY) 

 

CONSUMER NOTICE 

The  catalogue  description  and  any  exhibition  of  samples  are  only  broad  indications  of  the  Products  and  R&G  may  make  design  changes  which  do  not  diminish  their 
performance or visual appeal and supplying them in such state shall conform to the order. The Buyer acknowledges no representation or warranty (other than as to title) has 
been given or will  apply to the Products other than those  in  R&G’s order or confirmation and the Buyer confirms  it has chosen the Products as being of  merchantable 
quality and suitable for its particular purposes. Where R&G fits the Products or undertakes other services it shall exercise reasonable skill and care and rectify any fault free 
of  charge  unless  the  workmanship  has  been  disturbed.    The  Buyer  is  responsible  for  ensuring  that  the  warranty  on  the  motorcycle  is  not  affected  by  the  fitting  of  the 
Products. On return of any defective Products R&G shall at its option either supply a replacement or refund the purchase money but shall not be liable if the Products have 
been modified or used or maintained otherwise than in accordance with R&G’s or manufacturer’s instructions and good engineering practice or if the defect arises from 
accident  or  neglect.  Other  than  identified  above  and  subject  to  R&G  not  limiting  its  liability  for  causing  death  and  personal  injury,  it  shall  not  be  liable  for  indirect  or 
consequential loss and otherwise its liability shall be limited to the amounts paid by the Buyer for the Products or the fitting or service concerned. These terms do not affect 
the Buyer’s statutory rights. 

 
 

R&G RACING RETURNS POLICY (NON-FAULTY GOODS) 

Returns must be pre-authorised (if not pre-authorised the return will be rejected). Goods may only be returned direct to us if they were purchased direct from us (customer 
must prove if necessary).  Otherwise to be returned to original vendor. Goods must be in re-sellable condition, in the opinion of R&G Racing. All returns are subject to a 
25% restocking and handling fee (25% of the gross value exc. P&P – at the prevailing price at time of purchase). The customer must pay any and all carriage charges. No 
returns of discontinued products, unless within 14 days of purchase. This policy does not affect your statutory rights and d 

 

 
 

Summary of Contents for PKS0059







Reviews: