background image

                                       

                             LP0197 

 

R&G Racing 

Unit 1, Shelley’s Lane, East Worldham, Alton, Hampshire, GU34 3AQ 

Tel: +44 (0)1420 89007  Fax: +44 (0)1420 87301  

www.rg-racing.com

  Email

[email protected]

 

14

 

 

Page | 14 

 

Vérifiez que les clignotants et les feux de plaque fonctionnent bien avant de prendre la 
route.

 

 
 

Notice disponible au téléchargement sur 

www.rg-racing.com

 

 

C

OUPLES DE SERRAGE RECOMMANDES

 

 

M4 BOULON = 8Nm 

M5 BOULON = 12Nm 
M6 BOULON = 15Nm 
M8 BOULON = 20Nm 

M10 BOULON = 40Nm 

 

ISSUE 4  04/11/2016 (HH) 

 

CONSUMER NOTICE 

The catalogue description and any exhibition of samples are only broad indications of the Products and R&G may make design 
changes which do not diminish their performance or  visual appeal and supplying them in such state shall conform to the order. 
The Buyer acknowledges no representation or warranty (other than as to title) has been given or will apply to the Products other 
than those in R&G’s order or confirmation and the Buyer confirms it has chosen the Products as being of merchantable quality 
and  suitable  for  its  particular  purposes.  Where  R&G  fits  the  Products  or  undertakes  other  services  it  shall  exercise  reasonable 
skill  and  care  and  rectify  any  fault  free  of  charge  unless  the  workmanship  has  been  disturbed.    The  Buyer  is  responsible  for 
ensuring that the warranty on the motorcycle is not affected by the fitting of the Products. On return of any defective Products 
R&G  shall  at  its  option  either  supply  a  replacement  or  refund  the  purchase  money  but  shall  not  be  liable  if  the  Products have 
been  modified  or  used  or  maintained  otherwise  than  in  accordance  with  R&G’s  or  manufacturer’s  instructions  and  good 
engineering practice or if the defect arises from accident or neglect. Other than identified above and subject to R&G not limiting 
its liability for causing death and personal injury, it shall not be liable for indirect or consequential loss and otherwise its liability 
shall be limited to the amounts paid by the Buyer for the Products or the fitting or service concerned. These terms do not affect 
the Buyer’s statutory rights. 

 
 

R&G RACING RETURNS POLICY (NON-FAULTY GOODS) 

Returns must be pre-authorised (if not pre-authorised the return will be rejected). Goods may only be returned direct to us if they 
were purchased direct from us (customer must prove if necessary).  Otherwise to be returned to original vendor. Goods must be 
in re-sellable condition, in the opinion of R&G Racing. All returns are subject to a 25% restocking and handling fee (25% of the 
gross  value  exc.  P&P  –  at  the  prevailing  price  at  time  of  purchase).  The  customer  must  pay  any  and  all  carriage  charges.  No 
returns of discontinued products, unless within 14 days of purchase. This policy does not affect your statutory rights and does not 
refer to faulty goods. 
 

 
 

  

 
 

Summary of Contents for LP0197BK















Reviews: