manualshive.com logo in svg

Ramsey Electronics BULLSHOOTER ENDLESS LOOP BS2C, Assembly And Instruction Manual, Page: 3 / 28

Share
Download
Ramsey Electronics BULLSHOOTER ENDLESS LOOP BS2C Assembly And Instruction Manual Download Page 3

BS2 

•

 3  

THE BULLSHOOTER 

ENDLESS LOOP 

VOICE RECORDER   

Ramsey Publication No. MBS2 

Price $5.00 

TABLE OF CONTENTS 

 

Introduction ............................................ 4 
Circuit Description.................................. 5 
BS2C Parts List...................................... 7 
Parts Layout Diagram ............................ 9 
Assembly Procedure............................ 10 
Schematic Diagram.............................. 14 
Initial Testing and Operation ................ 20 
Using the BS2C ................................... 20 
Case Up Instructions............................ 25 
Troubleshooting ................................... 26 
Warranty............................................... 27 

KIT ASSEMBLY 

 AND INSTRUCTION MANUAL FOR 

RAMSEY ELECTRONICS, INC. 

590 Fishers Station Drive 

Victor, New York 14564 

Phone (585) 924-4560 

Fax (585) 924-4555 

www.ramseykits.com 

Summary of Contents for BULLSHOOTER ENDLESS LOOP BS2C





























Reviews:

No comments