manualshive.com logo in svg

Ramsey Electronics BULLSHOOTER ENDLESS LOOP BS2C, Assembly And Instruction Manual, Page: 26 / 28

Share
Download
Ramsey Electronics BULLSHOOTER ENDLESS LOOP BS2C Assembly And Instruction Manual Download Page 26

BS2 

•

 26  

TROUBLESHOOTING 

Won’t record from Microphone and/or Line In. 

1.  Check to make sure you have the proper recording mode selected. The 

decimal point on the numeric display indicates the mode. If in microphone 
mode, the LED is off. If in line-record mode, the LED is on. Check your 
source and be sure you don’t have both an external microphone and a 
line level audio source plugged in at the same time. 

2.  You have to press BOTH PLAY and RECORD at the same time. This is to 

prevent accidental erasures by bumping the wrong key. 

The LEDs work, but nothing else happens. 

1.  Make sure U3 and U2 are properly seated and there are no bent-over or 

bent under pins. 

2.  Make sure you have your speaker properly wired. 

No LEDs light 

1.  Check for 3.3VDC on the output pin of the regulator. 

2.  Make sure your power adapter is between 5 and 12VDC, center pin posi-

tive. Alternately you can run the kit from 4 AA cells in series to get 6V. 

 
The #@$%! Thing won’t work! Ramsey engineers know nothing! 

Shall we direct you to the warranty at the end of this manual? (ummm, on the 
next page) We also have a BBS to help you at  
 
http://www.ramseyelectronics.com 
 
Thanks for putting this great product together! 
 
-The Ramsey Team. 

Summary of Contents for BULLSHOOTER ENDLESS LOOP BS2C





























Reviews:

No comments