background image

TURBORAM  |  

Edition C - Revision 4

Instruction Manual  |  

3

  1 | Technical data

Colocar etiqueta

com especificações técnicas

OVEN MANUFACTURER:

Ramalhos, S.A.

Rua Arrota de Baixo, 823
Covão  · ZI EN1 Norte
3750-802 Águeda  · Portugal

Tel. +351 234 630 200
Fax +351 234 630 209

[email protected]

www.ramalhos.com

 

 ·  This device is not intended for use by people (including 

children) whose physical, sensory or mental capacities 
are reduced or people who lack experience or knowledge 
unless they are supervised by someone responsible 
for their safety or have previously received instructions 
regarding the use of the device.

 

 ·  It is recommended that children be supervised to ensure 

that they do not play with the device.

   ·  The user of the device should avoid looking directly at 

the light bulbs when they are on.

 

 

Symbol for Dangerous Voltage

 

 

Equipotential Connection

RECOMMENDATIONS FOR THE CLEANING OF THE OVEN

 

 · Do not clean the equipment with jets of water.

 

 ·  Do not clean the glass with cold water when the glass is 

hot.

 

 · Avoid the use of corrosive products.

 

 · If there are any doubts, contact RAMALHOS.

   ·  When this device is positioned near a dividing wall, 

furniture, decorative accessories, etc., it is recommended 
that they be non-combustible and thermally insulated. 
Special attention should be given to the fire prevention 
regulations.

1.1  TECHNICAL RECOMMENDATIONS

Summary of Contents for TURBORAM


















Reviews: