Raisecom RC801-60B-FV35 Series User Manual Download

Page: 24 / 30

Raisecom Technology Co., Ltd

5. Installation & Preparation

5.1. Before installation

Please make sure that your V.35 cable matches the equipment you want to connect

Please check whether the equipment has been destroyed

If you do not use network management, please configure the device through
DIP-switch before installation.

The E1 interface is 75

BNC in default, if Balance interface is needed please

configure the SW7 on the bottom of device.

Using of E1 balanced interface cable
The definition of each pin on E1 balanced interface is
shown in below table:

NO.

1 2 3 4 5 6 7 8

Signal

Name

TD+ TD- N/A RD+ RD- N/A N/A

N/A

Meaning Output -

Input +

Input -

When connect the 120

Ω

balanced interface to other device, the pin definition of the device

should be aware. The connection type of twisted pair cable is shown as following:

Modem

BALANCE-RJ45 E1Transmission Device Balanced Interface

＋

Signal Output

＋

－

Signal Output

－

＋

Signal Input

＋

－

Signal Input

－

NOTE: The TD+ and TD- should be two lines which are twisted together. And it is the
same to RD+ and RD-.

5.2. Cautions before Applying the Power Supply

It is strictly forbidden to hot-swap the V.35 interface cable.

If adopts the DC –48V power supply, please firstly connect the Protecting Ground (the
middle pin PGND). They must not be reversely connected, connect -48V with low
voltage input, BGND with high voltage input.

Summary of Contents for RC801-60B-FV35 Series































Search results

Summary of Contents for RC801-60B-FV35 Series

Reviews:

Related manuals for RC801-60B-FV35 Series

Brands by name

Popular brands

Raisecom RC801-60B-FV35 Series, User Manual

Search results

Summary of Contents for RC801-60B-FV35 Series

Reviews:

Related manuals for RC801-60B-FV35 Series

Brands by name

Popular brands