Raisecom RC801-60B-FV35 Series User Manual Download Page 19

Page: 19 / 30

Raisecom Technology Co., Ltd

OFF

Tributary

Bidirectional

loopback disable

Tributary

Bidirectional

loopback disable

Remote Loopback

Tributary V.35 interface remote bidirectional loopback sketch map:

Above figure is the result of configuring remote bidirectional loopback of 1

tributary V.35

interface on “local fiber optic modem”. At the same time the remote fiber optic modem’s
loopback dip-switch should be all OFF in default.

Tributary V.35 interface local bidirectional loopback sketch map:

Above figure is the result of the configuring local bidirectional loopback of 1

tributary V.35

interface on “local fiber optic modem”. At the same time the remote fiber optic modem’s
loopback dip-switch should be all OFF in default.

Tributary E1 interface remote bidirectional loopback sketch map:

Above figure is the result of the configuring remote bidirectional loopback of 2

tributary

E1 interface on “local fiber optic modem”. At the same time the remote fiber optic modem’s
loopback dip-switch should be all OFF in default.

Tributary E1 interface local bidirectional loopback sketch map:

Above figure is the result of the configuring local bidirectional loopback of 2

tributary E1

interface on “local fiber optic modem”. At the same time the remote fiber optic modem’s
loopback dip-switch should be all OFF in default.

Local Fiber

Optic Modem

Remote Fiber

Optic Modem

V.35 Error Code

Equipment

Fiber

V.35

V.35 Error Code

Equipment

V.35

Local fiber

optic modem

Remote fiber

optic modem

V.35 Error code

equipment

Fiber

V.35

V.35 Error code

equipment

V.35

Local Fiber

optic modem

Remote Fiber

optic modem

E1 Error code

equipment

Fiber

V.35

E1 Error code

equipment

Local fiber

optic modem

Remote fiber

optic modem

E1 Error code

equipment

Fiber

V.35

E1 Error code

equipment

V.35

Summary of Contents for RC801-60B-FV35 Series































Search results

Summary of Contents for RC801-60B-FV35 Series

Reviews:

Related manuals for RC801-60B-FV35 Series

Brands by name

Popular brands

Raisecom RC801-60B-FV35 Series, User Manual

Search results

Summary of Contents for RC801-60B-FV35 Series

Reviews:

Related manuals for RC801-60B-FV35 Series

Brands by name

Popular brands