Raisecom ISCOM RAX711 Product Description Download

Page: 53 / 67

Raisecom
ISCOM RAX711 (B)Product Description

Raisecom Technology Co., Ltd.

Table 6-9 lists PIN definitions on the serial interface on the PC.

Table 6-9

PIN definitions on serial interface on PC

PIN

Definition

PIN

Definition

PIN 1

DCD

PIN 6

DSR

PIN 2

RxD

PIN 7

RTS

PIN 3

TxD

PIN 8

CTS

PIN 4

DTR

PIN 9

PIN 5

GND

–

Figure 6-7 shows the wiring between PINs on the ISCOM RAX711 and PINs on the PC.

Figure 6-7

Wiring between PINs on device and PINs on PC

6.1.5 Fiber

Introduction

The ISCOM RAX711 supports single-mode and multi-mode fiber.

Table 6-10 lists fiber connectors available for the ISCOM RAX711.

Table 6-10

Fiber connectors

Local connector

Remote connector

Fiber

LC/PC

2 mm single-mode fiber

2 mm multi-mode fiber

LC/PC

FC/PC

2 mm single-mode fiber

2 mm multi-mode fiber

LC/PC

SC/PC

2 mm single-mode fiber

2 mm multi-mode fiber

Summary of Contents for ISCOM RAX711




































































Search results

Summary of Contents for ISCOM RAX711

Reviews:

Related manuals for ISCOM RAX711

Brands by name

Popular brands

Raisecom ISCOM RAX711, Product Description

Search results

Summary of Contents for ISCOM RAX711

Reviews:

Related manuals for ISCOM RAX711

Brands by name

Popular brands