background image

 6' min. 

 6' min. 

2x Swing

Beam Height

2x Swing

Beam Height

 6' min. 

 6' min. 

Choosing a location for your play system

When selecting your play site, always keep the child's safety in mind.  Here are some recommendations that should help you achieve a safe 

play area.
 1.  The play system should be located on solid level ground free of objects that could cause injury such as, but not limited to, tree stumps, 

      roots, and large rocks.  Stationary components such as ladders and slides must be no less than SIX FEET (1.8 meters) from any 

      structure or obstruction such as a fence, garage, house, tree or overhanging branches, electrical wires or clotheslines.  Any swinging 

      equipment must be a minimum distance of TWICE the height of the swing beam away from any structures or obstructions as specified 

      above.  We also recommend that you do not install your play system near a lake, river, swimming pool or other water hazards.

 2.  If anchoring your play system, all underground utilities must be located in play zone before starting assembly of play system. 

 3.  Try to locate slide out of direct sunlight to reduce the likelihood of serious burns.  A slide that faces north will receive the least direct 

      sunlight.

 4.  It is recommended not to place a set on sandy soil or loose fill as it may require additional anchoring in that situation.

 5.  Do not install your play system over concrete, asphalt, packed earth, grass, carpet, or any other hard surface.  A fall onto a hard surface 

      can result in serious injury to the play system user.

Choosing a surfacing material

The consumer shall provide playground surfacing materials under and around residential play equipment that conforms to the 

recommendations of the Consumer Product Safety Commission's Outdoor Home Playground Safety Handbook publications #324.  A copy 

of the section relating to surfacing materials is included in the installation instructions.  Free copies of this handbook are available on line at 

www.cpsc.gov or by contacting the CPSC Publications Office in Washington D.C. 20207.  

Playground equipment should never be placed on hard surfaces such as concrete or asphalt.  Do not use loose fill surfacing on top of hard 

surfaces such as concrete or asphalt.  While grass may appear to be acceptable, it may quickly turn to hard packed earth in areas of high 

traffic.  Shredded bark mulch, wood chips, fine sand or fine gravel are considered to be acceptable shock absorbing surfaces when installed 

and maintained at a sufficient depth under and around playground equipment.  The U.S. Product Safety Commission (CPSC) estimates that 

about 100,000 playground equipment-related injuries resulting from falls to the ground surface are treated annually in U.S. hospital's 

emergency rooms.  Injuries involving this hazard pattern tend to be the most serious of all playground injuries, and have a potential to be 

fatal, particularly when the injury is to the head.  The surface under and around playground equipment can be a major factor in determining 

the injury-causing potential of a fall.  It is self evident that a fall onto a shock absorbing surface is less likely to cause a serious injury than a 

fall onto a hard surface.  
The following information is intended to assist in comparing the relative shock-absorbing properties of various materials.  No particular 

material is recommended over another.  However, each material is only effective when properly maintained.  Materials should be checked 

periodically and replenished to maintain correct depth as determined necessary for your equipment.  The choice of a material depends on 

the type and height of your playground equipment, the availability of the material in your area, and its cost.
Table 3.1 lists the maximum height from which a child would not be expected to sustain a life-threatening head injury in a fall onto four 

different loose-fill surfacing materials if they are installed and maintained at depths of 6, 9, and 12 inches.  However, it should be recognized 

that all injuries due to falls cannot be prevented no matter what surfacing material is used. 

The URL is http://www.cpsc.gov/cpscpub/pubs/324.pdf and the file size is 456.5KB

Set Dimensions 

Play Zone

L 15' x W 13 1/2' x 

H 9 1/2'

L 27' x W 27 1/2'

3

Summary of Contents for Super Funhouse




































Reviews: