background image

9 / 12

IMPORTANT NOTE: 

Although this section can be used as a quick start guide, we 

strongly suggest that you read the entire manual before proceeding. This checklist is 

NOT intended to replace the content included in this instruction manual.

 

- Always turn the transmitter on first.

- Ensure the throttle control stick is at bottom position before connecting the battery.

- Fly the model (hand-launch or take off from a flat/level surface). 

- Land the model (on a flat/level surface).

- Unplug the battery from ESC.

- Always turn off the transmitter last.

Flight Checklist

Binding is the process of programming the receiver to recognize the 

GUID (Globally Unique Identifier) code of a single specific transmitter. When a receiver 

is bound to a transmitter, the receiver will only respond to that specific transmitter. 

Binding Instructions

If you need to rebind for any reason, please follow the steps below.

1. Keep the transmitter switched OFF with the throttle stick at bottom position.

NOTICE:

 Keep PASS switch at Partial or Full assist position. 

NOTICE:

 Make sure you keep the plane still in a calm, stable position when initializing  

 

   the PASS system.

 

2. Connect the battery to the plane, then turn on the transmitter within 5 seconds. 

3.The receiver LED will flash for 3 to 8 seconds before binding automatically. 

4. After the receiver LED stops flashing, the binding process is complete and you are  

    ready to fly. 

 

CAUTION: 

Remember to use caution when flying near people and property!

Summary of Contents for MICRO WARBIRD Series













Reviews: