background image

N

OTICE

© 2000-2008 RADVISION Ltd. All intellectual property rights in this publication are owned 
by RADVISION Ltd and are protected by United States copyright laws, other applicable 
copyright laws and international treaty provisions. RADVISION Ltd retains all rights not 
expressly granted. 

This publication is RADVISION confidential. No part of this publication may be reproduced 
in any form whatsoever or used to make any derivative work without prior written approval 
by RADVISION Ltd. 

No representation of warranties for fitness for any purpose other than what is specifically 
mentioned in this guide is made either by RADVISION Ltd or its agents. 

RADVISION

 Ltd reserves the right to revise this publication and make changes without 

obligation to notify any person of such revisions or changes. RADVISION Ltd may make 
improvements or changes in the product(s) and/or the program(s) described in this 
documentation at any time. 

If there is any software on removable media described in this publication, it is furnished 
under a license agreement included with the product as a separate document. If you are 
unable to locate a copy, please contact RADVISION Ltd and a copy will be provided to 
you. 

Unless otherwise indicated, RADVISION registered trademarks are registered in the 
United States and other territories. All registered trademarks recognized.

For further information contact RADVISION or your local distributor or reseller. 

SCOPIA Gateway version 5.6, June 2008

Publication 9

http://www.radvision.com

62782-00001 Rev A03

Summary of Contents for SCOPIA 100





















Reviews: