background image

-

5

-

PATIO HEATER ASSEM LY

ASSEM LY INSTRUCTIONS

List of Required Tools: Philips Screwdriver

Leak Detection Solution one part detergent and three parts water

A em le all n t an

olt loo el at ir t Ti

ten all onne tion a ter om letion o a em l

T i ea e

o r wor an in rea e t e ta ilit o t ea

lian e

efore assembly, make sure all packing material and any transmit protection must be removed.

Small deviations in equipment may occur.

If any part is missing or damaged, do not attempt to assemble this product, Contact customer service for
replacement parts.

Assembly should be performed on a flat, level, non-abrasive surface.

ESTIMATED ASSEM LY TIME: 45 minutes.

STEP :

Lay down tank housing assembly ( ) as

shown above. Take off the door and take out all parts.

STEP :

eep the burner with the igniter side up. Fix

the burner assembly ( ) to tank housing using 4pcs M5
Screws and Washers (

).

STEP :

nscrew 2pcs M5 screws and washers (

) preassembled in Support ar

Lower (F).

Insert upper Support ar (E) to lower Support ar (F) and fix the connection using 2pcs screws and washers
(

). Repeat this step and connect other 3 sets of support bars.

Summary of Contents for H1501A

















Reviews: