background image

- 10 -

LEAK TESTING

NE ER USE A NAKED FLAME TO CHECK FOR LEAKS
NE ER LEAK TEST WHILE SMOKING

The gas connections on this appliance are leak tested at the factory prior to
shipment.
This appliance needs to be periodically checked for leaks. and an
immediate check is required if the smell of gas is detected.

Make a soap solution using 1 part liquid dish-washing soap to 3 parts
water. The soap solution can be applied with a soap bottle, brush, or rag
to the leak tested points shown in the figure above.

The valve of the gas cylinder should be in the

OFF

position at this point of

the leak test. Once the soapy solution is applied to the gas connections,
the valve of the gas cylinder needs to be turned to the

ON

position.

Soap bubbles will begin to form in the soapy solution if a leak ispresent.

In case of a leak, turn off the gas supply. Tighten any leaking fittings, then
turn the gas supply on and recheck.

GAS RE UIREMENTS

The appliance must use an EN12864 or EN16129 approved gas regulator and CE approved gas hose with a
length of 20in ( S3212 and EN1 63-1). Choose the proper regulator according to outlet pressure in the
technical table in page 14.
You will need to purchase a suitable gas hose and regulator from your local gas dealer, If the appliance does
not include a gas hose and regulator.

Never use a gas cylinder with a damaged body, valve, collar, or foot ring. A dented or rusty gas tank may be
hazardous and should be checked out by a gas supplier.

Never connect this appliance to an unregulated gas source.

When the appliance is not in use, turn the gas cylinder OFF.

Always perform a leak test on gas connections whenever a cylinder is connected. If bubbles form in the leak test
solution, do not use. Never use a flame to test for leaks.

CONNECTING TO A GAS CYLINDER

It is recommended you use a max. 33lb or smaller gas cylinder (maximum height 25in) refer to your gas
supplier for suitable gas cylinder.

An approved gas regulator is used according to appliance categories and countries listed in data plate. An
approved flexible hose would be changed when the national conditions require it.

Assembly of the tubing must be conducted by a qualified personnel in destination countries.

Only change gas cylinders outdoors or in a well-ventilated area away from naked flames and any other source of
ignition (candle, cigarettes, other flame producing appliances .).

The gas cylinder must always be used in an upright position.

Close the heater control knob by turning fully clockwise.

Close the gas cylinder tap and then attach the regulator onto the gas cylinder.

Tighten all connections firmly and with a spanner where appropriate. The cylinder should be located on the
cylinder base.

C e

or lea

at all oint

in

oa

water I a lea i o n

ti

ten t e oint an t en re te t

Summary of Contents for H1501A

















Reviews: