background image

-

2

-

Check the tubing or the flexible hose per month and each time the cylinder is changed.

The tubing or the flexible hose must be changed within the prescribed intervals or within one year.

The hose assembly must be replaced prior to the appliance being put into operation if there is evidence of
excessive abrasion or wear, or if the hose is damaged. A specified replacement hose assembly shall be
used.

The heater should be inspected before use and at least annually by a qualified service person. More frequent
cleaning may be required as necessary. It is imperative that the control compartment, burners and circulating
air passageways of the appliance be kept clean.

Shut off and check heater immediately if any of the following conditions exist:
D

The smell of gas in conjunction with extreme yellow tipping of the burner flames.

D

Heater does not reach a proper temperature. A temperature less than 40 degrees Fahrenheit will cause
restricted heat flow and the appliance will not workproperly.

D

The appliance starts making popping noises during use (a slight popping noise is normal when
the appliance is extinguished).

The regulator & hose assembly must be located out of pathways where people may trip over it, or in an area
where the hose will not be subject to accidental damage.

Any guard or other protective device removed for servicing the heater must be replaced before operating the
heater.

Children and adults should be warned of the hazards of high surface temperatures and should stay away to
avoid burns or clothing ignition.

Young children and pets should be carefully supervised when they are in the area of the heater.

Clothing or other flammable materials should not be hung from the appliance or placed on or near the
appliance.

Do not place articles on or against this appliance. Certain material or items when stored under or near this
appliance will be subjected to radiant heat and could be seriously damaged.

Do not use or store flammable materials near this appliance.

Do not spray aerosols in the vicinity of this appliance while it is in operation.

Always maintain at least 36 in clearance from combustible materials.

Always position the appliance on a firm level surface. An amply ventilated area must have a minimum of 25% of
the surface area open. The surface area is the sum of the walls surface.

Summary of Contents for H1501A

















Reviews: