background image

12

2.4 Other hydraulic functions

2.4.1 Flexible leveller - raising

Upon pressing, the key will highlight in yellow and the 

fl

 exible leveller will beging to rai-

se. Press it again and the key will highlight in green and the 

fl

 exible leveller raising stops.

2.4.2 Flexible leveller - lowering

Upon pressing, the key will highlight in yellow and the 

fl

 exible leveller will beging to 

lower. Press it again and the key will highlight in green and the 

fl

 exible leveller lowering 

stops.

2.4.3 Mulching section raising

Pressing this key will turn on the mulching sec  on raising func  on. To end the raising, 
press the key again and the mulching sec  on raising func  on will turn o

 .

2.4.4 Mulching section lowering

Pressing this key will turn on the mulching sec  on lowering func  on. To end the lowe-
ring, press the key again and the mulching sec  on lowering func  on will turn o

 .

2.4.5 Pre-emergent marking of tramline

Pressing this key will turn on the pre-emergent tramline marking func  on. The func  on 
enabling is indicated by yellow color of the key. Its subsequent func  ons are derived 
from the tramline valves func  on. In case the tramline valves close and unsown marks 
are created, the pre-emergent marking automa  cally lowers. Upon opening of the val-

ves, the pre-emergent marking raises. By pressing the 

 key again, the 

pre-emergent tramline marking func  on turns o

 .

2.4.6 Markers automatics

Pressing this key will turn on the func  on of automa  c switching-over of the markers 

at the dead centre. The key will be highlighted in yellow 

. By this, the 

automa  c switching-over is enabled and the posi  on of markers will always automa  -
cally change a  er raising.

2.5 Procedure with the markers automatic switching-over function enabled:

If the automa  c func  on 

 

is enabled in the second screen, use the  

 key to return to the 

fi

 rst screen.

Now, based on which side of the 

fi

 eld you intent to start, press either the le   or right marker lowering key. 

Prior to the selec  on of the marker, the seed drill must be uncondi  onally raised, both keys must be grey-co-
loured and the markers symbols on the icons must point upwards. A  er pressing the marker corresponding 
key, both markers will turn green and the symbol of the pressed marker will point down. Immediately a  er the 
start of the drill lowering, the pre-selected marker will lower as well. At the ride end, during the drill raising, 
both marker keys will switch-over and the lowered marker will automa  cally raise. At the subsequent lowe-
ring of the drill, the second marker will start lowering.

Summary of Contents for A100





















Reviews: