background image

5

1.9 Night and day mode change

Pressing the display in the date and   me displaying area will invoke the night mode 
display which is less highlighted and does not disturb during work at night. Pressing the 
same area again will return the day mode display.

1.10 Seeding mechanism speed

Displays the actual value of seeding mechanism speed during the drill opera  on. The 
speed range is within a scale of 0 rpm to 255 rpm. The maximal speed range is given by 
the manufacturer and is derived from the width and the maximal travel speed of the 
drill. In case the seeding mechanism stops during drill opera  on, a zero speed value is 
displayed and an acous  c signal is sound to alert the operator about this serious fault. 
In case the speed value is lower or higher than the required speed, the speed numerical 
value is highlighted in red and an acous  c signal is sound. This signals to the operator 
that he must either reduce the seeding assembly travel speed or stop the drill and check 

the seeding mechanism for possible faults. To manually stop the doser, press the 

 

speed numerical value. By this, the 

STOP

 symbol will be displayed instead of the speed 

value and the doser motor will be blocked during driving. By pressing the 

STOP

 symbol, 

the doser motor will return to the standard opera  on mode.

Summary of Contents for A100





















Reviews: