RADIXON WR-G35DDC EXCALIBUR ULTRA User Manual Download Page 87 | Manualshive

Page: 87 / 128

background image

WiNRADiO G35DDC User’s Manual

87

Demodulator Filter Length

The

Demodulator filter length

has a direct influence upon the

Excalibur

Ultra

’s selectivity. Greater length gives better selectivity.

The maximum achievable selectivity is limited by the processing power of your
computer: The greater the CPU power, the “longer” (and therefore sharper)
can the filter be made.

This function also makes it possible to observe the

CPU load

, which will

depend on this setting. It may not be advisable to select a value resulting in
more than say 30% CPU load, as the computer may then become sluggish.

Should the computer become sluggish or even “freeze” as a result of this
adjustment, please reduce the demodulator filter length to a lower value.

Note also that the CPU load can be lowered (while keeping selectivity high) by
reducing the DDC bandwidth (

DDC BW

). All standard HF signals can be

demodulated with 20 kHz DDC bandwidth without decrease in demodulation
quality. Wider DDC bandwidths affect display and recording, while increasing
the CPU load considerably.

«
...
85
86
87
88
89
...
»

Summary of Contents for WR-G35DDC EXCALIBUR ULTRA

































































































































Reviews:

No comments

Related manuals for WR-G35DDC EXCALIBUR ULTRA

Brand: Ramsey Electronics Pages: 28

Personal PA Receiver PPA R35N

Brand: Williams Sound Pages: 6

Brand: Ericsson Pages: 3

Brand: Audiotech Pages: 7

Brand: GEOSUN Pages: 9

Brand: Boss Audio Systems Pages: 18

Brand: Zenith Pages: 70

Brand: Yaesu Pages: 20

Brand: Sole Digital Pages: 17

Brand: Yaesu Pages: 45

Brand: Crestron Pages: 10

Brand: Tactic Pages: 2

Brand: PowerBass Pages: 12

WPS818C SAORVIEW

Brand: Walker Pages: 24

AUDIO-B PLUS aptX TWS

Brand: Tinysine Pages: 7

Brand: Dilog Pages: 71

Brand: Kramer Pages: 67

Brand: Kenwood Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands