RADIXON WR-G35DDC EXCALIBUR ULTRA User Manual Download Page 64 | Manualshive

Page: 64 / 128

background image

WiNRADiO G35DDC HF Receiver

64

2. If the AGC is enabled and the sound is distorted despite the volume being
turned down, make sure that the AGC reference level is not set too high. If the
volume is too low, try to increase the AGC reference level.

3. If the AGC is disabled and the sound is too weak despite the volume control
being all the way up, try to increase the manual gain.

4. In LSB, USB, ISB, DSB and CW modes, manual gain is often preferable to
automatic gain because there is no “carrier” the AGC would act upon and
maintain at a constant level. If AGC is used, then the

slow

setting is

preferable.

Noise Blanker

The

Noise Blanker

can be used for removal of random high-level noise-spikes

resulting from atmospheric effects and man-made interference.

There are two types of noise blankers available, one using the

Short Time

DDC Averaging

method and another one using the

ADC Input Threshold

method.

The

Short Time DDC Averaging

method is based on comparing the

instantaneous signal level at the DDC output (demodulator input) to a short-
time exponential average. If the instantaneous level exceeds the short-time
average, these samples will be replaced with zeros.

With the

ADC Input Threshold

method, the blanking effect occurs much

earlier in the signal processing chain: The signal samples at the input of the

ADC are compared to a threshold value, and, if greater, then these samples
are zeroed.

The

Short Time DDC Averaging

method is preferable and will yield

improvement in most cases of atmospheric or man-made interference. It is
activated by pressing the

Enable DDC Averaging

button located under the

«
...
62
63
64
65
66
...
»

Summary of Contents for WR-G35DDC EXCALIBUR ULTRA

































































































































Reviews:

No comments

Related manuals for WR-G35DDC EXCALIBUR ULTRA

Brand: Clarion Pages: 162

Brand: Magnadyne Pages: 12

Brand: Alpine Pages: 71

Brand: DSC Pages: 5

Brand: Audiotech Pages: 7

Brand: Xoro Pages: 78

Brand: Aria Pages: 12

Brand: RF Central Pages: 41

Brand: Kantronics Pages: 10

Brand: GTX Pages: 7

Brand: Cambridge Audio Pages: 13

Brand: YOKOGAWA Pages: 2

Digital Freeview Receiver

Brand: Tevion Pages: 2

Brand: Yaesu Pages: 68

Brand: BFT Pages: 2

Brand: Icom Pages: 24

Brand: TEUCER Pages: 4

Brand: HITEC Pages: 5

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands