RADIXON WR-G35DDC EXCALIBUR ULTRA User Manual Download Page 72

Page: 72 / 128

WiNRADiO G35DDC HF Receiver

Right-clicking on the spectrum reveals a menu with the following functions:

Tune to nearest peak

– this will tune the receiver to a peak that is nearest to

the cursor. The capture area is 15 pixels either side of the cursor (the actual
frequency range will vary depending on the current zoom status).

Place marker

– this will place a marker to the current cursor position.

If a marker exists next to the cursor, additional functions become available:

Set marker reference

– this will set this particular marker as a reference from

which frequency differences will be calculated and displayed for the other
markers. The reference marker will be marked with an

next to its displayed

frequency. The differential value with respect to the reference marker will be
displayed next to the other markers:

Did you know?

The WiNRADiO AX-17C (

www.winradio.com/ax17c

) is a

miniature indoor active HF antenna suited for applications
where it is not possible to use conventional large outdoor
antennas, and where loop antennas are either not
available or not practical due to their large size.

Summary of Contents for WR-G35DDC EXCALIBUR ULTRA

































































































































Search results

Summary of Contents for WR-G35DDC EXCALIBUR ULTRA

Reviews:

Related manuals for WR-G35DDC EXCALIBUR ULTRA

Brands by name

Popular brands

RADIXON WR-G35DDC EXCALIBUR ULTRA, User Manual

Search results

Summary of Contents for WR-G35DDC EXCALIBUR ULTRA

Reviews:

Related manuals for WR-G35DDC EXCALIBUR ULTRA

Brands by name

Popular brands