Radio Shack 900 MHz Digital Spread Spectrum Cordless Phone with Dual Caller..., Owner'S Manual

Page: 18 / 28

18
Operation
Follow these steps to store a number and
name in the handset.
1. Lift the handset.
2. Hold down
MEM
until
C[cehoýIjeh[ C[cehoýIjeh[ C[cehoýIjeh[ C[cehoýIjeh[
and a
list of memory location numbers (and
names, if any) appear.
3. Select an empty memory location (or the
one you want to replace) by using
VOL/
CID
8
8 8
8
or
9
9 9
9
to scroll through the list or
entering the location number (01–20).
Precede a single-digit number with a 0
(01, for example).
Note: If the phone sounds five quick
beeps, you have made an entry error
and the number was not stored. Reenter
the location number correctly.
4. Press
SELECT/INTCM
.
Ijeh[ Ijeh[ Ijeh[ Ijeh[ DWc[ DWc[ DWc[ DWc[
appears. If you do not want to enter a
name, skip to Step 6.
5. To enter a name, use the number keys.
Refer to the letters on the number keys
to select the desired letter. Press the key
once for the first letter in the upper case,
press twice for the second letter in the
upper case, and so on. To enter the
lower case letter, press four times (or
five times) to display the first letter in
lower case, five or six times for the sec-
ond letter, and so on.
For example, to enter John: press
5
once; upper case
@@@@
appears. Then press
6
six times; lower case
eeee
appears. Press
4
five times; lower case
^^^^
appears.
Finally, press
6
five times; lower case
dddd
appears.
To enter two letters from the same key in
a row, press
FLASH
7
7 7
7
to move the cur-
sor to the next position. For example to
enter AB, press
2
;
7777
appears. Then
press
FLASH
7 7 7 7
, the cursor moves to the
next position, then press
2
twice so
8888
appears.
To enter a space, press
FLASH
7
7 7
7
twice
without entering any character.
To enter a number, repeatedly press the
corresponding number key until the
number appears.
To enter special character, use
0
. Each
time you press
0
, the following charac-
ters appear in this order:
∗∗∗∗
# – &
ýýýý
( ) (space) 0
If you make a mistake, use
REDIAL
6 6 6 6
or
FLASH
7
7 7
7
to move the cursor over the
error, then enter the correct character, or
press
DELETE/CH
to delete a character.
To delete all characters, hold down
DELETE/CH
for at least 1 second.
6. Press
SELECT/INTCM
.
Ijeh[ Ijeh[ Ijeh[ Ijeh[ DkcX[h DkcX[h DkcX[h DkcX[h
appears.
7. Enter the phone number and any tone or
pause entries (see “Entering a Pause”
on Page 19).
If you make a mistake, use the same
method to correct it as described in Step
5.
8. Press
SELECT/INTCM
. The phone beeps
and
C[cehodd C[cehodd C[cehodd C[cehodd Ijeh[Z Ijeh[Z Ijeh[Z Ijeh[Z
(nn stands for the
memory location number you assigned)
appears. After 2 seconds,
C[ceho C[ceho C[ceho C[ceho Ijeh[ Ijeh[ Ijeh[ Ijeh[
appears. Repeat Steps 3–8 to store
more numbers.
9. When you finish, press
MEM
.
To replace a stored number, store a new one
in its place (see “Editing or Deleting a Num-
ber in the Handset's Memory” on Page 19).