Radio Shack 43-3704 Owner'S Manual Download

Page: 50 / 76

Expanding Your

Phone

EXPANDING YOUR

PHONE

Dual Handset Expandability

Your phone supports another handset in

addition to the supplied. You can now place

a fully-featured cordless handset anywhere

AC power is available to connect the

handset charger.

Handsets can be used in DirectLink Mode

or on an intercom call without interfering

with incoming calls. It is possible to have a

four-way conference among two handsets

and both outside lines. All of the handsets

ring when a call is received.

EGISTER

THE

ANDSET

THE

ASE

If you purchase an extra handset, you need

to register the handset to the base before

use. Only one handset can be registered at

a time.

Handset supplied with the phone is

registered to the base by the factory. When

charged, pre-registered handset displays a

handset ID number. Handset that has not

been registered displays

Place handset

on main base to register

. When

you register an extra handset to the base,

the handset ID will be assigned.

1. Before registering the extra handset,

the battery pack MUST be charged for
15-20 hours.

2. Place the extra handset in the main

base unit to begin registration.

3. While the handset is registering,

Handset Registering

will appear

in the LCD.

IMPORTANT

If you purchase a 43-3705
extra handset, please
register the handset to the
original/main base before
use. The 43-3705 will not
operate until it is registered.

NOTES

• All of the handsets ring

when a call is received.

• An extra handset can be

registered when the
main base is in standby
mode.

Summary of Contents for 43-3704













































































Search results

Summary of Contents for 43-3704

Reviews:

Related manuals for 43-3704

Brands by name

Popular brands

Radio Shack 43-3704, Owner'S Manual

Search results

Summary of Contents for 43-3704

Reviews:

Related manuals for 43-3704

Brands by name

Popular brands