manualshive.com logo in svg

R-Tech PLASMA 80HF, Operation Instructions Manual

The R-Tech PLASMA 80HF ensures smooth operation thanks to its high-frequency start and pilot arc feature. For a seamless user experience, make sure to download the free Operation Instructions Manual from manualshive.com. This manual will guide you through the product setup and maintenance for optimal performance.

Share
Download
background image

 

11

 

Operating machine 

 

SAFETY PRECAUTIONS 

 

WARNING! 

 

 
ELECTRIC SHOCK CAN KILL 
 
Do not touch electrically live parts or electrode with skin or wet clothing. 
Insulate yourself from work and ground 
Always wear dry insulating gloves 

 

WARNING! 

 

 
FUMES AND GASES can be dangerous 
 
Keep your head out of fumes & gases produced from welding. 
Use ventilation or exhaust to remove fumes & gases from breathing zone and general 
area.

 

WARNING! 

 

 
WELDING SPARKS can cause fire or explosion 
 
Keep flammable material away from work area. 
Do not weld on containers that have held combustibles 
 

WARNING! 

 

 
ARC RAYS can burn 
 
Wear eye, ear and body protection – Make sure work area is protected by proper shielding 
to avoid injury to passers by. 
 
 
 
 
 
 
 
 
 
 

Summary of Contents for PLASMA 80HF




















Reviews:

No comments

Related manuals for PLASMA 80HF

Brands by name

Popular brands

Load more brands