background image

Operating hints

PAGE 11

One Pass
Burnishing

Steps: (see below)

1.  Turn machine on with the key switch.

2.  Lower burnishing head to the floor by simply
depressing the black burnisher deck button.

3.   Begin burnishing by holding the green
control button onthe the handle bar.

4.  Adjust the red speed control knob to desired
speed located on the side of the central
command box.

5.  Once the pad begins to move, check the
pressure gauge.  Start burnishing with in the
green marks, do not use yellow marks without
management approval.

6.  To operate machine in reverse, simply pull
back on red togel switch located on the right
hand side of central command box.

7.  To stop the machine, let go of the green
control button and the machine will stop
automatically.

Operation

Read and understand the safety section on page
5 and 6 before operating machine.

Pre- burnishing
Check list

1.   Check battery condition gauge on the hour
meter/battery gauge.

(See below)

 Make sure

batteries are fully charged before using.

2.    Check condition of pad and make sure it is
securely in place.

3.    Check hose connections from the motor to
the frame are secure.

(See below)

5.    Check condition of shroud curtain the
shroud curtain needs to be in good condition for
dust control system to work properly.

(See below)

1

2

3

5

4

6

BATTERY GAUGE

HOUR METER

Summary of Contents for 200


























Reviews: