R-Biopharm KOBRA CELL Instruction Manual Download Page 12

12

R-Biopharm Rhone Ltd

4.4

  Installation Instructions

Caution:

 Do not over tighten. Cell connections 

should be made with plastic ferrules, not metal. 

1.  Unpack the KOBRA® CELL and check that all of 
 

the components are present.

2.  Add 119 mg of potassium bromide and 350 µl of 
 

4 M nitric acid to 1 l of mobile phase.

3.  Immerse the tubing from the HPLC pump into 
 

the mobile phase.

4.  Disconnect the storage plugs and capillary 
 

tubing from the KOBRA® CELL. Connect the 

 

HPLC column discharge to the KOBRA® CELL 

 

inlet using plastic ferrules (hand tightened) and 

 

a length of PEEK

TM

 tubing supplied with the kit.

5.  Connect the KOBRA® CELL outlet using ferrules 
 

(hand tightened) and a length of PEEK

TM

 tubing 

 

to the detector inlet according to the table 

 below.

 

Caution:

 Use a guillotine tubing cutter to 

 

prevent distortion of the diameter of the tubing.

6.  Connect the detector outlet to the KOBRA® CELL 
 

inlet using plastic ferrules (hand tightened) and 

 PEEK

TM

 tubing.

7.  Connect the KOBRA® CELL outlet to waste using 
 

plastic ferrules (hand tightened) and PEEK

TM

 

 tubing.

8.  Switch on the HPLC pump and flush mobile 
 

phase through the system for approximately 

 

5 minutes.

9.  Connect the KOBRA® CELL power pack to the 
 

cell, red lead to red terminal and black lead to 

 

black terminal.

 

Caution:

 Do not switch on without mobile 

 

phase flowing through the KOBRA® CELL or the 

 

membrane will be damaged.

10. After the HPLC has been allowed to stabilise 
 

(approximately 30 minutes) the KOBRA® CELL is 

 

ready to use.

Determination of Reaction Coil / PEEK

TM

 Tubing Length

Flow Rate

0.5 ml/min

0.6 ml/min

0.7 ml/min

0.8 ml/min

0.9 ml/min

1.0 ml/min

Internal 

diameter 

of reaction 

coil / 

PEEK

TM

 

tubing (id)

0.2 mm

106.1 cm

127.3 cm

148.5 cm

169.8 cm

191.0 cm

212.2 cm

0.25 mm

67.9 cm

81.5 cm

95.1 cm

108.6 cm

122.2 cm

135.8 cm

0.4 mm

26.5 cm

31.8 cm

37.1 cm

42.4 cm

47.7 cm

53.1 cm

0.5 mm

17.0 cm

20.4 cm

23.8 cm

27.2 cm

30.6 cm

34.0 cm

0.6 mm

11.8 cm

14.1 cm

16.5 cm

18.9 cm

21.2 cm

23.6 cm

0.8 mm

6.6 cm

8.0 cm

9.3 cm

10.6 cm

11.9 cm

13.3 cm

1.0 mm

4.2 cm

5.1 cm

5.9 cm

6.8 cm

7.6 cm

8.5 cm

Summary of Contents for KOBRA CELL

























Reviews: