V2.1 / 14.03.2019
FUM5-00AM-DES-G5021
27
Operating and Installation Instructions Q gateway 5 - EN
Mounting point requirements:
0DNHVXUHWKHUHLVDVXႈFLHQWO\VWURQJ*608076VLJQDODWWKHPRXQWLQJSRLQW
The GSM/UMTS signal strength can be determined at the gateway via the control menu, using the
*6080760RQLWRU
IXQFWLRQ
VHH6HFWLRQ³&DOO&RQWURO0HQX´RQSDJH,IWKH*608076VLJQDOLVWRRORZZKLOHWKHJDWHZD\LVRSHUDWLQJÄ/RZ6LJ³
appears on the display. Move the Q gateway 5 to a location with a better GSM/UMTS signal and repeat the process.
Ensure an adequate radio link is available to a RNN5 of the Q AMR network to be read out.
,IGXULQJWKHQHWZRUNVFDQWKHGLVSOD\RIWKHUDGLRVLJQDOVWUHQJWKLQGLFDWHVWKHVLJQDOOHYHOLVWRRORZFKDQJHWKHSRVLWLRQZLWKLQ
the building and repeat the procedure.
7KHGLVSOD\RIWKHUDGLRVLJQDOVWUHQJWKFDQDOVREHGHWHUPLQHGDWWKHJDWHZD\RႉLQHZLWKRXWOLQNWRWKH
Q SMP
YLDWKH&RQWURO
menu using the
Scan
IXQFWLRQVHH6HFWLRQ³&DOO&RQWURO0HQX´RQSDJH
The minimum distance between the Q gateway 5 and a Q AMR network node should be 3 metres.
The following tools are necessary for correct mounting:
•
6WUDLJKWVORWVFUHZGULYHUIRUVLPSOHRSHQLQJRIWKHKRXVLQJFRYHU
• Cross-slot screwdriver or cordless screwdriver
•
PPVWRQHGULOOIRUGULOOLQJWKHSOXJKROHVPPLQWKHZDOO
•
In addition for Q gateway 5 RNG5N00R1x:
3UHLQVWDOOHGPDLQVFRQQHFWLRQ9$&+]
Before wall mounting
• Open the housing cover.
• Plug the battery connector into the power supply connector
6
.
$IWHUFRQQHFWLRQWRWKHSRZHUVXSSO\4JDWHZD\DQLQLWLDOL]DWLRQSURFHVVLVVWDU
-
ted. The green LED
5
ÀDVKHV
• Close the battery compartment
7
.
•
6FUHZWKHHQFORVHGFDEOHJODQGIURP
the outside through the through-hole
on the
KRXVLQJRIWKH4JDWHZD\
.
RNG5N00R1x only
• Open the housing cover.
•
&RQQHFWWKHSOXJFRQQHFWRURIWKH
power supply board
14
with the plug
FRQQHFWRUIRUWKHSRZHUVXSSO\
6
on
the main board using the enclosed
mains connection cable.
• Insert the enclosed hexagon nut
IURP
the inside in
IURQWRIWKHWKURXJKKROHRQ
the
KRXVLQJRIWKH4JDWHZD\
.
To do this, push the nut into the guide
UDLODVIDUDVLWZLOOJR
RNG5N00R1x only
6
14
6