background image

PRE-INSTALLATION CONTROL 

 

Before installing the automation, you must check that the gate’s shutter: 

-

  The leaf turn freely in the hinges and without sticking in the ground 

-

  It does not swing during its movement; 

-

  is kept in axis by the special hinges; 

-

  the leaves have the proper stoppages when opening and closing. 

 
Borinato  F.lli  Snc  is  liable  only  for  products  it  manufactures  and  commercializes.  Once 
automated,  the  gate  becomes  a  machine  and  is  therefore  subjected  to  the  rules  of  the  “ 
Machinery Directive”. It is on the installer to verify its security. WARNING: Borinato F.lli Snc is 
not  liable  for  any  damages  to  people,  animals  or  things  due  to  unauthorised  modifications, 
alterations or  betterments on its products by third parties.  
 
GENERAL ADVICE 
 
Install a gate’s safety system that complies with current regulations. Choose short routes 
for cables and keep power cables separate from control ones. Install the control card in a 
waterproof box. 
Please refer to current regulations when setting the gear motor’s maximum torque. 
We advice you to install an outdoor switch, in compliance with European standards on the 
issue of safety, to turn the electricity off when servicing the gate. 
Check that each single installed device is efficient and effective. 
Affix easily readable signs warning about the presence of a motorised gate.  
 
USE 
It is absolutely forbidden to use the device for any other purposes. Installed control board 
(which must have built-in electric friction), allows selecting the following functions: 
automatic: one control impulse will open or close the gate; 
semi-automatic: one control impulse will open or close the gate. 
In  case  of  blackout,  act  on  the  manual  unlocking  device  and  move  manually  the  gate. 
Remember that this is an automatic device powered by electricity, consequently use with 
care. In particular, remember: 

-

  not to touch the device with wet hands and/or wet or bare feet; 

-

  to turn off electricity before opening the control box and/or actuator; 

-

  not to pull the lead to pull the plug out; 

-

  to put the gate in movement only when it is completely visible; 

-

  to keep out of the gate’s range of action if it is moving. Wait until it has stopped; 

-

  not to let children or animals play near the gate; 

not to let children use the remote control or other operating devices 
 

 
 
 
 
 

Summary of Contents for QK-H300













Reviews: