background image

LUCCA M58 

   

 

Owner’s Manual 

Page 4 

 

  Periodically the pump will come on by itself to maintain the proper water level in the 

boiler. Sometimes the pump will come on when you turn on the machine and 
sometimes it may not depending on the water level in the boiler which is normal. 

  The pump (brew) pressure is regulated by the expansion valve. To learn how to set 

the pump pressure, please refer to the maintenance section of the owner’s manual.    
 

Water Reservoir (Tank) 

 

 

  The water reservoir can be accessed by opening the hinged reservoir door on the 

top of the machine. It is recommended that the reservoir be removed prior to filling 
to prevent the spilling of water inside the machine which can cause damage to 
sensitive electrical components. Should water accidently get spilled inside the 
machine then immediately turn the power switch to the off position and unplug the 
machine from the electrical outlet. Do not plug the machine back in until it has had 
at least 1 full day to dry out. If it does not operate after that time then unplug the 
machine and refer to the troubleshooting section of the owner’s manual. 
 

  The reservoir must be installed properly for the machine to function. The float 

inside the reservoir must be on the left side of the machine. Also be sure the 
reservoir is seated as far down as possible and the silicone hoses are not pushing 
the float down or the PID and heating lights will not turn on. 

  The machine is equipped with a magnetic float in the water reservoir to detect the 

water level. When the water level gets low the PID and heating lights will go out and 
the pump will no longer function until the reservoir has been refilled. 

  The reservoir should be cleaned at least once a week with mild dish detergent and 

rinsed thoroughly before use. 

DO NOT PUT IN DISHWASHER!!!

 

  Depending on your water quality it may be necessary to periodically sanitize the 

reservoir or if you are using hard water and have a mineral build up inside. White 
vinegar can be used to sanitize and will also remove the mineral deposits that can 
accumulate.  

 

Summary of Contents for LUCCA M58
























Reviews: