manualshive.com logo in svg

Quest 88 Trikes, User Manual, Page: 20 / 20

Share
Download
Quest 88 Trikes User Manual Download Page 20

Quest 88 Tricycles -  Limited Warranty

QUEST 88 TRICYCLE FRAMES AND FORKS ARE WARRANTED BY THE COMPANY: FOR THE FIRST 5 YEARS FROM DATE OF PURCHASE 
AGAINST ANY DEFECTS IN MATERIALS AND WORKMANSHIP.  OTHER PARTS OF THE TRICYCLE ARE WARRANTED FOR TWO YEARS 
FROM DATE OF PURCHASE AGAINST DEFECTS IN MATERIALS AND WORKMANSHIP. THIS WARRANTY IS FREELY TRANSFERABLE.  
TRANSPORTATION CHARGES ARE ALSO COVERED.

QUEST 88 WILL REPLACE WITHOUT CHARGE ANY FRAME  AND/OR FORK FOUND TO BE DEFECTIVE  BY THE FACTORY WITHIN 
THE TERMS OF THE WARRANTY. (REPLACEMENTS WILL BE THE SAME OR SIMILAR IN CONSTRUCTION AND COSMETICS , BUT WILL 
BE LIMITED TO CURRENT STOCK) HOWEVER, QUEST 88 WILL ASSUME LABOUR CHARGES INVOLVED ONLY IN FRAME AND FORK 
REPLACEMENT AND LIMITED TO 90 DAYS FROM THE DATE OF PURCHASE AT RETAIL.

QUEST  88  TRICYCLES  ARE  NOT  MANUFACTURED  OR  SOLD    FOR  USE  INVOLVING  RAMP  JUMPING,  PASSENGERS,  NOR  ARE 
THEY INTENDED TO BE USED WITH MOTORS, ENGINES OR OTHER POWER EQUIPMENT. PRODUCT PERFORMANCE AND USE IS 
DETAILED IN THE USER INSTRUCTIONS. THE COMPANY, IT'S AUTHORIZED AFFILIATES OR AGENTS SHALL NOT BE LIABLE UNDER 
THIS WARRANTY OR ANY LAWS FOR ANY DAMAGE OR FAILURE INCLUDING PERSONAL INJURY, RESULTING FROM IMPROPER USE. 

PERSONAL INJURY, BICYCLE FAILURE, LOSS OR DAMAGE, ABUSE, NEGLECT, NORMAL WEAR (SUCH AS TYRES AND TUBES, BRAKE 
AND GEAR CABLES, SEAT, PEDALS AND HANDLEBAR GRIPS/TAPES), IMPROPER FIT OR MAINTENANCE BY ANYONE OTHER THAN 
THE COMPANY OR AUTHORIZED AGENTS, OR USE OF PARTS INCONSISTENT WITH THE USE ORIGINALLY INTENDED FOR THE 
TRICYCLE AS SOLD ARE NOT COVERED BY THIS. AUTHORIZED AGENT PURSUANT TO THIS WARRANTY HEREIN MADE SHALL BE 
THE REPLACEMENT OF THE DEFECTIVE PART(S), AND IN NO EVENT SHALL QUEST 88 LIMITED BE LIABLE FOR INCIDENTAL OR 
CONSEQUENTIAL DAMAGES. 

SPECIAL NOTES TO USERS, PARENTS, GUARDIANS AND/OR SUPERVISORS

WE DO RECOMMEND THAT YOU CONTACT US IMMEDIATELY IF YOU EXPERIENCE ANY DIFFICULTY WHATSOEVER. TOTAL 
SUPERVISION WILL BE REQUIRED IF THE USER HAS LIMITED SKILLS ESPECIALLY COMMUNICATION - PLEASE NOTE, ALL SAFETY 
LABELS MUST BE REPLACED IF THEY BECOME WORN - CONTACT QUEST 88 LIMITED IF IN DOUBT. REGULAR INSPECTION 
AND MAINTENANCE IS ESSENTIAL TO ENSURE THAT THE PRODUCT PERFORMS TO CLIENTS EXPECTATIONS AT ALL TIMES.

Dear Customer

,

Thank you for purchasing a Quest 88 tricycle. We sincerely hope that this tricycle will meet all of 

your expectations. As part of our Product Vigilance System and our commitment of service to 

you, this form serves as  warranty confirmation for your trike. Please keep these details in a safe 

place as this will help us maintain traceability for your trike. If you wish to contact us in the future 

please quote the FRAME CODE (below, also found on the inspection label on back of chain guard).

Manufacture Completed on:     ________________  

Model Name:   KITTEN / COLT / CAROUSEL / PANTHER

Frame Number:    QU _

_____________

Quest 88 limited, Aston Street, Shifnal, Shropshire, TF11 8DW

tel: +44 (0)1952 463050     fax: +44 (0)1952 463077     www.quest88.com     email:[email protected]

QD. TRINST1supp.PM6 iss.7/GJ-06/09

20

Summary of Contents for Trikes





















Reviews:

No comments