4
Trouble Condition
Visual Indications
Audible Indications
Action:
low battery
Amber
LED
blinks
every
5
seconds
Chirp every 60 sec, voice every
30 sec: “Replace alarm.”
Voice stops after 5 mins.
*Remove, discharge, dispose unit, and replace
as soon as possible.
Fault mode
Chirp every 30 sec.
Voice every 30 sec: “Error, see
trouble shooting guide”
After 5 mins: no voice message
*See Cleaning Your Alarm section.
* Push Test/Hush button once to attempt to
reset the unit .
*Red LED will blink out an error code (number
of blinks) when Test/Hush button is push/
released once. Report the number of blinks to
customer service if needed.
end of Unit life
Double chirp every 30 sec.
First 5 mins: Voice every 30 sec:
“Replace alarm, press button to
silence.” Voice stops after 5 mins.
After 7 days: Chirps continue.
Voice every 30 sec for 5 mins:
“Replace alarm.”
* Push/release Test/Hush button to temporarily
silence (see End of Unit Life Hush Mode section
below)
* Remove, discharge, dispose unit, and replace
as soon as possible.
end of Unit life hush
mode (after push/
release test/hush
button during end
of life)
Voice “Temporarily Silenced.”
End of Unit Life chirps silenced
for 24 hrs. (7 days after End of
Unit Life chirps begin, the chirps
cannot be silenced.)
* Remove, discharge, dispose unit, and replace
as soon as possible.
network error
Chime every 30 secs. Voice
every 30 sec: “Connection Lost.
Press Button to Silence.”
After 5 min: no voice messages
(Note: network must have
3 or more alarms for voice
messages.)
* Push/release the Test/Hush button once to
silence for 24 hrs at a time.
*Red LED will blink out an error code (number
of blinks) when Test/Hush button is push/
released once. Report the number of blinks to
customer service if needed.
* Push and hold Test/Hush button until two
beeps are heard (approx 4 sec) and then release
the button to try to rejoin. Or reset (section 7.3)
and then rejoin (section 7.2).
*If error persists, remove, discharge, and replace
alarm as soon as possible.
network error hush
(after button push
during network error)
Voice “Temporarily Silenced.”
4. Introduction, Product Features and Specifications
Introduction
This alarm detects products of combustion using photoelectric technology. Ten (10) years after the unit was installed,
this unit will automatically alert you that it is time to replace the unit. This is called “End of Unit Life” mode. See Section 3
Troubleshooting Guide.
To help identify the date to replace the unit, a label has been affixed to the side of the alarm. Write the “Install date” in
the space provided, and then write in the “Replace by” date (10 years from initial power up) in permanent marker on the
label prior to installing the unit.
Product Features and specifications:
•
Temperature: Operating Range: 0 °C to 40 °C
•
Humidity: Operating range: up to 93% RH non-condensing
•
Audible Alarm: 85+ dB at 10’ @ 3.0 to 3.5 KHz pulsing alarm, with voice message “Fire!”
note:
This is not a CO alarm, but it will receive and transmit a CO alarm signal (with voice message
“Warning! Carbon Monoxide”) from an interconnected CO or combination smoke/CO alarm.
•
Smoke Sensor: Photoelectric
•
Voice message system
•
Smoke Alarm SMART HUSH Control
•
Ambient Light Sensing
•
Powered by 3V DC non-replaceable sealed lithium battery.
•
Wireless interconnectable to other compatible alarms.
•
One large, user- friendly button.
•
LED safety light on model
Q4000LDCS-WCH and Q4000LDCS-WBH
to help illuminate escape pathways.
