background image

 

 

SC20-W_Manual_R1.0                                      Confidential / Released                                                39 / 41

 

 
 
 

9

 

IC & FCC Requirement 

9.1. 

FCC Regulations: 

This  device  complies  with  part  15  of  the  FCC  Rules.  Operation  is  subject  to  the  following  two 

conditions: (1) This device may not cause harmful interference, and (2) This device must accept any 

interference received, including interference that may cause undesired operation. 

This device has been tested and found to comply with the limits for a Class B digital device , pursuant 

to  Part  15  of  the  FCC  Rules.  These  limits  are  designed  to  provide  reasonable  protection  against 

harmful  interference  in  a  residential  installation.  This  equipment generates,  uses  and  can radiated 

radio frequency energy and, if not installed and used in accordance with the instructions, may cause 

harmful interference to radio communications. However, there is no guarantee that interference will 

not  occur  in  a  particular  installation  If  this  equipment  does  cause  harmful  interference  to  radio  or 

television  reception,  which  can  be  determined  by  turning  the  equipment  off  and  on,  the  user  is 

encouraged to try to correct the interference by one or more of the following measures: 
 

-Reorient or relocate the receiving antenna. 

-Increase the separation between the equipment and receiver. 

-Connect  the  equipment  into  an  outlet  on  a  circuit  different  from  that  to  which  the  receiver  is 

connected. 

-Consult the dealer or an experienced radio/TV technician for help. 

 

Caution: Changes or modifications not expressly approved by the party responsible for compliance 
could void the user„s authority to operate the equipment. 

9.2. 

RF Exposure Information 

This device complies with FCC radiation exposure limits set forth for an uncontrolled environment. In 

order to avoid the possibility of exceeding the FCC radio frequency exposure limits, human proximity 

to the antenna shall not be less than 20cm (8 inches) during normal operation.

 

9.3. 

ISED Notice 

This device complies with Innovation, Science and Economic Development Canada license-exempt 

RSS standard(s). Operation is subject to the following two conditions: 

(1) this device may not cause interference, and   

(2)  this  device  must  accept  any  interference,  including  interference  that  may  cause  undesired 

operation of the device. 

Summary of Contents for Smart Wi-Fi Module Series












































Reviews: