Quarrix StormStop Installation Instructions Manual Download Page 7 | Manualshive

Page: 7 / 13

background image

INSTALLATION INSTRUCTIONS

ATTIC PROTECTION

Quarrix.com

|

800.438.2920

7

Attach vent to the roof deck by driving a nail or a #8 screw in each of the

two corners on both ends of the vent. Also, drive two nails or #8 screws

through the vent and foam end cap to hold foam in place on the ends of

the ridge only. Fasteners should penetrate the wood roof deck at least

3

⁄

4

”.

It is recommended to fasten the vent to ridge prior to stone-coated steel

hip/ridge cap installation. Vent should be secured every 5”.

4. Cap Shingle Installation

It  is  important  when  installing  this  vent  that  you  maintain  the  pitch  of  the
roof.  The  vent  has  been  installed  properly  if  the  bottom  of  the  vent  is  flat
on  the  roof  and  the  peak  is  slightly  rounded.  Install  hip/ridge  caps  per
manufacturer’s installation guide. Each hip/ridge piece should clip together
by inserting the return (at the nose of each piece) into the back clip, which is
located at the top of the hip/ridge cap section. Fasten cap to vent through
the back clip using #8 screws. Fasteners should penetrate through the wood
roof deck at least

3

⁄

4

”.

4

SteelRoofs

STONE-COATED

INST-SSRV01.0

2

.0

4

.21

Distributed by Best Materials® LLC

http://www.bestmaterials.com | 1-800-474-757

[email protected] |

http://www.bestmaterials.com | 1-800-474-7570

[email protected] | http://www.bestmaterials.com | 1-800-474-7570

http://www.bestmaterials.com | 1-800-474-757

[email protected] |

http://www.bestmaterials.com | 1-800-474-7570

[email protected] | http://www.bestmaterials.com | 1-800-474-7570

«
...
5
6
7
8
9
...
»

Summary of Contents for StormStop














Reviews:

No comments

Related manuals for StormStop

Brand: Fanimation Pages: 20

Andover FP5220 Series

Brand: Fanimation Pages: 16

WhisperGreen FV-08VKM3

Brand: Panasonic Pages: 15

Brand: Omega Altise Pages: 5

ASHBURTON YG593-WH

Brand: HAMPTON BAY Pages: 21

Fireball Turbo-Fan 9000

Brand: SIP Pages: 8

AirVolution-D 550

Brand: MacroAir Technologies Pages: 76

RIRS EKO 3.0 1200 HE

Brand: Salda Pages: 40

Brand: GSi Pages: 44

Brand: Casablanca Pages: 2

Brand: AirKing Pages: 2

Brand: Gaggenau Pages: 32

Brand: ebm-papst Pages: 13

Brand: ebm-papst Pages: 10

Brand: ebm-papst Pages: 13

Brand: ebm-papst Pages: 13

Brand: ebm-papst Pages: 12

Northwind CF702ORB04

Brand: Emerson Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands