background image

6

Installing the Internal LTO-3 Half-Height Tape Drive

LTO-3 Half-Height Tape Drive Quick Start Guide

Figure 3  Internal Parallel SCSI 
Bus Termination Examples

 

    

After configuring the parallel SCSI ID and bus termination power, proceed to 

Mounting 

the Internal Tape Drive

 in the following subsection.

Mounting the Internal 
Tape Drive

0

You can mount the internal LTO-3 Half-Height Tape Drive either horizontally or 

vertically, but not upside down (see 

figure 4

). 

Figure 4  Acceptable Mounting 
Orientations

Note:

The internal parallel SCSI LTO-3 Half-Height Tape Drive does not provide 

SCSI termination. The last device at the end of the parallel SCSI bus chain must 

have a SCSI bus terminator.

IF you mount the drive . . . 

THEN the . . . 

horizontally,

base of the drive must be within 15 degrees of 
horizontal.

vertically,

side of the drive must be within 5 degrees of 
horizontal.

Tape drive

 

(no termination)

SCSI device

 

(termination 
disabled)

SCSI controller

 

(termination 
enabled)

SCSI device 

 

(termination enabled)

Tape drive

 

(no termination)

SCSI controller

 

(termination enabled)

SCSI terminator

SCSI terminator

            YES                                YES                               YES                                                 NO

     

Summary of Contents for LTO3 A-Series

















Reviews: