background image

Electromagnetic Compatibility (EMC) Compliances

15

LTO-3 Half-Height Tape Drive

Electromagnetic Compatibility (EMC) Compliances

The LTO-3 Half-Height Tape Drives are EMC compliant with the following regulatory 

organizations and codes in the countries indicated:

Country

Regulatory Organization

Compliant to:

Australia

Australian Communications and 
Media Authority (ACMA)

AS/NZS 3548 (same 
as CISPR 22)

Canada

Industry Canada Digital Apparatus - 
Interference-Causing Equipment 
Standard 

 

(ICES-003)

ICES-003 Digital 
Apparatus

EU member nations

CE

Emissions per CISPR 
22, EN55022 and 
Immunity per CISPR 
24, EN55024

Israel

SII

CISPR 22 and CISPR 
24

Japan

Voluntary Control Council for 
Interface (VCCI)

VCCI

New Zealand

Australian Communications and 
Media Authority (ACMA)

AS/NZS 3548 (same 
as CISPR 22)

South Korea

MIC

CISPR 22 and CISPR 
24

Taiwan

Bureau of Commodity Inspection 
and Quarantine (BSMI)

BSMI EMC 
certification, CNS 
14338

United States

Federal Communications 
Commission (FCC)

Title 47: Code of 
Federal Regulations, 
Part 15, Subpart B 
(47CFR15B), 

Note:

Use these drives only in equipment where the combination has been 

determined to be suitable by an appropriate certification organization (for 

example, Underwriters Laboratories Inc. or the Canadian Standards 

Association in North America).

Summary of Contents for LTO3 A-Series

















Reviews: