background image

ActiveScale™ X100 Site Requirements Guide

25

Output Voltage

Branch Circuit Characteristics

Output Connector Ratings

Dimensions and weights

2.3.6  Load balancing PDUs

When selecting a PDU for use with the ActiveScale X100 it is important to consider how to balance the 

electrical load of the system on the PDU to prevent damaging power equipment or the system itself.

2.4  Build space requirement for rackless systems

The rackless version of ActiveScale X100 is designed to be delivered on multiple pallets and installed on 

site. Because of this, it is important to be sure that enough space is available for the individuals that will 

build the system to work.
While installing system components, there needs to be a minimum of 1220mm (48") of space at the front 

of the rack to allow for the space needed for the largest system component to be installed by a two people.

Nominal

230VAC

Operating Range

220VAC-240VAC

Number of Branches

2

Total Available Steady State Current (per branch)

16A, balanced

Short Term Peak (per branch)

<=20A

C13 Steady State Current

10A

C13 Short Term Peak Current

15A

C19 Steady State Current

16A

C19 Short Term Peak Current

20A

Width

2.2 in. / 55 mm

Height

69 in. / 1753 mm

Depth

2.25 in / 57 mm

Weight

18 lbs. / 8.2 kg

Summary of Contents for ActiveScale X100






























Reviews: