9 0
Q U A L I T Y F R Y
9 0
Q U A L I T Y F R Y
FAULT
POSSIBLE CAUSES
SOLUTIONS
THE MACHI-
NE DOES
NOT TURN
ON
The machine is unplugged.
Plug the machine into the mains.
There is no voltage or current in the
plug socket where it is connected.
Check that the mains plug socket or
switch works correctly.
The machine still doesn’t turn on.
Contact Technical Support
THE MACHI-
NE ASKS FOR
MORE OIL
(Perform
this process
when the oil
is cold)
Not enough oil was added to the
machine
Make sure you have added 5.5 litres
of oil.
The machine continues to ask for oil.
Clean the heating element and the
resistor, especially the float.
Bad connection between the angled
cable and the resistor.
Check that the black gasket is inside the
heating unit.
The float is not working.
Contact Technical Support
THE OIL
OVERFLOWS
FROM THE
VAT
Too much oil has been added to the
machine.
Remove the excess oil until you reach
5.5 litres.
Warning: Perform this process when
the oil is cold.
The round gasket has not been placed
on the fryer’s outlet ramp.
Place the gasket and tighten the black
flywheels that fasten the outlet ramp.
The round gasket is broken or warped.
Change the gasket
The flywheels that fasten the exit ramp
of the fryer are incorrectly tightened.
Correctly tighten the flywheels.
The tap for draining the fryer is open or
is not closed correctly. (Red Tap).
Close the oil drain tap correctly. (Red
Tap).
There is lots sediment or food debris
inside the machine.
Completely clean the fryer case. After
cleaning, add 5.5 litres of oil to the
fryer.
FIND
IN
G
F
A
UL
TS
A
ND
B
A
SI
C S
O
LU
TI
O
N
S
Without messages on the screen
Summary of Contents for iQ 600
