background image

Using your Adventure Top

Your Adventure Top has been 

designed with

a fold-back “sunroof” feature

that gives you the ultimate

in open air experience!

Folding Back the Front Section of your Top

FIG 69

Your SkyMaster Fastback top has been designed with a fold back “sunroof” feature that gives you the ultimate in open 

air experience. To fold back your SkyMaster Soft Top:

1 . If driving, stop the vehicle and put in park. Unlatch your over door Attachments from the door

Surrounds.

2. Unlatch the front header from the windshield

3. Pushing up from the middle, fold back the top.

4. Make sure the center bow is secured through the sewn inside webbing strap.

The Hardware system can also be easily detached and folded down to the rear of the vehicle. Unlatch the front header 

from the windshield. Un-hook the over door bows from the door surround brackets (FIG A).

Next, un-hook the center bow from the door surround bracket (FIG B). Once un-hooked, the front header assembly and 

center bow should easily fold back to the rear of the vehicle and should tuck down behind the rear roll bars (FIG C). The 

center bow should stay attached to the soft top with the hook and loop fastener that covers the center bow.

FIG A

FIG B

FIG C

FIG 73

FIG 72

FIG 71

FIG 70

Make sure the hook and loop fastener are tightly secured to the center bow after the front sun roof is folded back.

Make sure that each side webbed loop is secured around the center bow. Both rear corner straps must also be

secure when the top is folded back These safety measures are designed to secure the top deck to the vehicle and

if not adhered to can cause injury, death and a serious accident.

WARNING  

As with most aftermarket parts for Jeep vehicles, this soft top has been tested to speeds of up to 75 MPH.

Do not exceed the posted speed limits with this top installed and make sure all straps and attachments are secure

before embarking on any long highway road trip. Always wear your seat belts when using this product!

WARNING  

Summary of Contents for QuadraTop 11113.1135













Reviews: