background image

 2 

 

 

 

 

                          7019-230C 

 

 

 

                 May 18, 2015

Santa Fe Pellet Insert

TABLE OF CONTENTS

     Safety Alert Key:

• 

DANGER! 

Indicates a hazardous situation which, if not avoided will result in death or serious injury.

•  WARNING!

 Indicates a hazardous situation which, if not avoided could result in death or serious injury.

•  CAUTION! 

Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.

• 

NOTICE:

 Indicates practices which may cause damage to the appliance or to property.

Important Safety Information ............3

A.  Appliance Certifi cation ......................................................3
B.  BTU & Effi ciency Specifi cations........................................3
C.  Glass Specifi cations .........................................................3
D.  Electrical Rating................................................................3
E.  Mobile Home Approved .................................................... 3

Getting Started ...................................4

A. Design, Installation & Location Considerations  ..........................4
B. Thermostat Wall Control Location......................................5
C.  Tools And Supplies Needed ..............................................5
D. Inspect Appliance and Components  .................................5
E. Install Checklist ..................................................................6

Dimensions and Clearances .............7

A.  Appliance Dimensions ......................................................7
B. Clearance To Combustibles, UL and ULC .........................8
C. Masonry and Zero Clearance Fireplaces ..........................9
D. Minimum Opening for Masonry 
     and Zero Clearance Fireplaces .........................................9
E. Hearth Extension ...............................................................9
F.  Floor Protection .................................................................9
G. Installation into a Factory-Built Fireplace .............................10
H. Installation into a Masonry Fireplace .................................11
I. Prefabricated Metal Chimney ..............................................11

Vent Information ...............................11

A.  Venting Termination Minimum Requirements ...................11
B.  Avoiding Smoke and Odors ..............................................12
C.  Negative Pressure ............................................................13
D.  Draft..... .............................................................................13
E.  Chimney and Exhaust Connection  ..................................13
F.  Equivalent Feet of Pipe  ....................................................14
G.  Pipe Selection Chart ........................................................14

Venting Systems ..............................15

A.  Full Reline With Outside Air - Horizontal...........................15
B.  Full Reline With Outside Air  - Vertical ..............................16

Appliance Set-Up .............................17

A.  Leveling System ...............................................................17
B. Outside Air Kit Instructions ................................................17
C. Optional Grille Removal and Installation ...........................18
D. Door Handle Removal .......................................................18
E.  Door Removal ...................................................................18
F.  Adjustable Hearth Support  ...............................................19
G. Panel and Trim Set ............................................................20
H. Thermostat Installation ......................................................20
I. Optional Log Set Placement Instructions ............................21

Mobile Home Installation .................22

Accessory List .................................23

Summary of Contents for SANTAFEI-MBK





























Reviews: