background image

P775218M

This fireplace insert is factory equipped for 40,000 BTU  input and can be converted to 

33,000 using a smaller orifice (provided in optional orifice kit P/N H5924 for Natural Gas 

or P/N H5925 for Propane Gas).

This appliance may be installed in an aftermarket permanently located, manufactured  home (USA only) or mobile 

home, where not prohibited by local codes. This appliance is only for use with the type of gas indicated on the rating 

plate. This appliance is not convertible for use with other gases, unless a certified kit is used.

Cet appareil peut installé dans une maison préfabriquée (mobile) déjà installée à demeure, si les réglements locaux 

le permettent. Ce appareil doit être utilisé uniquement avec le type de gaz indiqué sure la plaque signalétique.  Cet 

appareil ne peut être converti à d'autres gaz, sauf si une trousse de conversion est utilsée.

INSTALLER:  Leave this manual with the appliance.

CONSUMER:  Retain this manual for future reference.

INSTALLATEUR:  Laissez cette notice avec l'appareil.

CONSOMMATEUR:  Conservez cette notice pour consul-

tation ultérieure.

— Do not store or use gasoline or other flammable vapors 

and liquids in the vicinity of this or any other appliance.

— WHAT TO DO IF YOU SMELL GAS

•  Do not try to light any appliance. 

•  Do  not  touch  any  electrical  switch;  do  not  use  any 

phone in your building. 

•  Leave the building immediately.

• Immediately call your gas supplier from a neighbor’s 

phone.  Follow the gas supplier’s instructions. 

•  If  you  cannot  reach  your  gas  supplier,  call  the  fire 

department.

— Installation and service must be performed by a quali-

fied installer, service agency or the gas supplier.

       WARNING:
FIRE OR EXPLOSION HAZARD

Failure to follow safety warnings exactly could result 

in serious injury, death, or property damage.

       AVERTISSEMENT:
RISQUED'INDENDIE OU D'EXPLOSION

Le non-respect Des avertissements de sécurité pour-

rait d'entraîner des blessures graves, la mort ou des 

dommages matériels.

— Ne pas entreposer ni utilizer d’essence ni d’autres 

vapeurs ou liquides inflammables dans le voisinage 

de cet appareil ou de tout autre appareil.

— QUE FAIRE SI VOUS SENTEZ UNE ODEUR DE GAZ:

• Ne pas tenter d’allumer d’appareil.

• Ne touchez à aucan interrupteur. Ne pas vous servir 

des téléphones se trouvant dans le bâtiment où vous 

trouvez. 

•  Sortez immédiatement de bâtiment.

•  Appelez  immédiatement  votre  fournisseur  de  gaz 

depuis un voisin. Suivez les instructions du fournis-

seur. 

• Si vous ne pouvez rejoindre le fournisseur de gaz, 

appelez le service des incindies.

— L’installation et l’entretien doivent être assurés par 

un installateur ou un service d’entretien qualifié ou 

par le fournisseur de gaz.

12

/19

/20

14

INSTALLATION AND OPERATION

MODELS

Direct

-V

ent

Ravenna™

RDV33/40 

 SDVI33/40

A French manual is available upon 
request. Order P/N 775218CF.

Ce manuel d’installation est disponible 
en francais, simplement en faire la 
demande. Numéro de la pièce 775218CF.

P/N 775218M  REV. G  01/2015

Report # 14-164

C

US

Summary of Contents for Ravenna RDV33





































Reviews: