background image

4

05/22

8106-803B

D. Glass Specifications

This  appliance  is  equipped  with  5mm  ceramic  glass. 

Replace glass only with 5mm ceramic glass. Please contact 

your dealer for replacement glass.

E. Electrical Rating (on high)

115 VAC, 60 Hz, Start 2.6 Amps, Run .9 Amps

F. Mobile Home Approved

•  This appliance is approved for mobile home installations 

when not installed in a sleeping room and when an 

outside combustion air inlet is provided.

•  The structural integrity of the mobile home floor, ceiling, 

and walls must be maintained. 

•  The appliance must be properly grounded to the frame 

of the mobile home with #8 copper ground wire, and use 

only listed double-wall connector pipe.

•  Outside Air Kit, part 811-0872 or OAK-3 must be installed 

in a mobile home installation.

•  Appliance must be secured to mobile home structure.

G. Non-Combustible Materials

Material  which  will  not  ignite  and  burn,  composed  of  any 

combination of the following:

-  Steel

-  Plaster

-  Brick

-  Iron

-  Concrete

-  Tile

-  Glass

-  Slate

Materials  reported  as  passing 

ASTM E 136, Standard 

Test Method for Behavior of Metals, in a Vertical Tube 

Furnace of 750° C

.

H. Combustible Materials

Material  made  of/or  surfaced  with  any  of  the 

following materials:

-  Wood

-  Compressed Paper

-  Plant Fibers

-  Plastic

-  Plywood/OSB

-  Sheet Rock (drywall)

Any material that can ignite and burn:

 flame proofed or not, 

plastered or non-plastered.

I. Sleeping Room

When installed in a sleeping room it is recommended that 

3ft of vertical be installed prior to horizontally exiting the 

room and a smoke/CO alarm be installed in the bedroom. 

The size of the room must be at least 50ft³ per 1,000 Btu/hr 

stove input, if the stove exceeds the room size, outside air 

must be installed.

J. Stove Composition

These pellet burning stoves are made of steel, cast iron or 

a combination of both with a ceramic viewing glass. These 

stoves  incorporate  a  self-feeding  system  including  a  fuel 

storage hopper and a mechanical feed system which is 

controlled by a micro-processing control board. Each model 

contains a variable speed distribution blower to circulate 

room air through the heat exchanger and out to the room 

and a combustion blower which forces the exhaust out of 

the stove.

K. California - Prop65

This product and the fuels used to operate this product (wood), and the 

products of combustion of such fuels, can expose you to chemicals 

including carbon black, which is known to the State of California to 

cause cancer, and carbon monoxide, which is known to the State of 

California to cause birth defects or other reproductive harm. For more 

information go to: WWW.P65Warnings.ca.gov

WARNING

NOTE:

 

Hearth  &  Home  Technologies,  manufacturer  of 

this appliance, reserves the right to alter its products, 

their specifications and/or price without notice.

Improper  installation,  adjustment,  alteration,  service  or 

maintenance can cause injury or property damage.

For assistance or additional information, consult a qualified 

installer, service agency or your dealer.

•  Installation and use of any damaged appliance.

•  Modification of the appliance.

•  Installation other than as instructed by Hearth & Home 

Technologies.

•  Installation  and/or  use  of  any  component  part  not 

approved by Hearth & Home Technologies.

•  Operating  appliance  without  fully  assembling 

all components.

•  Operating appliance without legs attached (if supplied 

with appliance).

• 

Do NOT Over fire - If appliance or chimney connector 

glows, you are over firing.

Any such action that may cause a fire hazard.

Fire Risk

Hearth & Home Technologies disclaims any 

responsibility for, and the warranty will be 

voided by, the following actions:

WARNING

Summary of Contents for OUTFITTER-I
























Reviews: