background image

11

05/22

8106-803B

A. Venting Termination Minimum Requirements

J or K

X

V

M

I

H

A

V

G

B

V

V

A

B

V

F V

C

B

B

E

L

V

D

V

Electrical

Service

V

N

V

N

V

N

N

V

Inside Corner

FIXED 

CLOSED

OPEN

OPEN

FIXED 

CLOSED

V

X

G

G

Termination Cap

Air Supply Inlet

Gas Meter

Restricted Area

O

P

A

12 in.

Above Finish Grade (the grade surface 

must be a non-combustible material

B

12 in.

48 in. no OAK

Open door or window: below or to the side

B

12 in.

Open door or window: above

C

6 in.

Permanently closed window: above, below 

or to the side

D

18 in.

36 in. no OAK

Vertical  clearance  to  a  ventilated  soffi  t 

located above the terminal within a 

horizontal distance of 2 ft from the center-

line of the terminal 

E

12 in.

Clearance to unventilated soffi  t

F

12 in.

Clearance to outside corner

G

12 in.

Clearance to inside corner

H

36 in.

Above gas meter/regulator measured from 

horizontal center-line of regulator

I

36 in. USA

72 in. Canada

Clearance to service regulator vent outlet

J

12 in.

48 in. no OAK

Clearance  to  non-mechanical  air  supply 

inlet to the building or the combustions air 

inlet to any other appliance

K

10 ft horizontal

3 ft vertical

Clearance to mechanical air supply

L

7 ft.

Above paved sidewalk, paved driveway 

located on 

public

 property

M

12 in.

Under an open veranda, porch, deck or 

balcony

N

See Note 

below*

Electric service: above, below or to the side 

(location must not obstruct or interfere with 

access)

O

24 in.

Adjacent building, fences and protruding 

parts of the structure

P

12 in.

Clearance above roof line for vertical 

terminations

All minimum clearances are listed with an Outside Air Kit (OAK) installed, unless otherwise noted in table below.

24 in.

Above grass, top of plants, wood or any other combus-

tible

12 in.

36 in. no OAK

Clearance from any forced air intake of other appliance

12 in.

Clearance horizontally from combustible wall

15 in.

Vented directly through a wall, minimum length of 

horizontal pipe

6 in. horizontal

12 in. vertical

Minimum horizontal or vertical terminations must pro-

trude from wall

*NOTE: 

Consult local building, fi re offi  cials or authorities 

having jurisdiction. Local codes or regulations may require 

diff erent clearances.

NOTICE:

 Termination must exhaust above air 

inlet elevation.

• 

It is recommended that at least 60 inches (1.52m) of 

vertical pipe be installed when appliance is vented 

directly through a wall. This will create a natural draft, 

which will help prevent the possibility of smoke or odor 

venting into the home during a power outage. 

• 

It  will  also  keep  exhaust  from  causing  a  nuisance 

or hazard by exposing people or shrubs to 

high temperatures.

•  The safest and preferred venting method is to extend 

the vent vertically through the roof or above the roof.

NOTICE: Do NOT Terminate Vent:

• 

In any location that will allow fl ue gases or soot from 

entering or staining the building.

• 

In any location which could create a nuisance or hazard.

• 

In  any  enclosed  or  semi-enclosed  area  such  as  a 

carport, garage, attic, crawl space, under a sun deck or 

porch, narrow walkway.

•  Closely fenced area, or any location that can build up 

a concentration of fumes such as a stairwell, covered 

breezeway, etc.

Vent Information 

Summary of Contents for OUTFITTER-I
























Reviews: