background image

Grand Bay 40 Gas Freestanding  

Page 6

January 2000

January 2000

SAFETY NOTICES

This appliance should only be installed by a qualified installer.  It is approved for installation in a bedroom.  

Bedroom installation in Canada requires that the stove be connected to a thermostat.  The appliance must be 

electrically grounded in accordance with local codes, or the latest edition of the National Electric Code.  If 

no local codes exist, this appliance should be installed following the current codes:

             CAN/CGA-B149.1 ........................................................................ Natural Gas Installation Code 

             CSA-C22.1..................................................................................... Canadian Electrical Code

             ANSI Z223.1.................................................................................. National Fuel Gas Code

             ANSI NFPA-70.............................................................................. National Electrical Code

The control compartment, burner, and circulating air passageways MUST be kept clean and clear to allow 

for  adequate  combustion  and  proper  operation.    Provide  adequate  clearances  around  air  openings  and 

adequate accessibility clearance for service and operation.  NEVER obstruct the openings of the appliance 

or the vent termination on the exterior of the building.  NEVER vent the appliance to other rooms or 

buildings; this appliance must be vented ONLY to the outside.  During installation, be sure to maintain 

minimum  clearances  to  combustibles,  as  shown  on  page  9.   Always  contact  your  local  building 

department  or  fire  department  prior  to  installing  this  appliance.    If  required,  obtain  a  permit  before 

installing,  and  have  the  completed  installation  inspected.    Failure  to  do  this  could  jeopardize  your 

homeowner’s insurance.

The  area  around  the  appliance  MUST  be  kept  free  from  combustible  materials,  gasoline  and  other 

flammable vapors and liquids.

This appliance is hot during operation, and should be located out of heavy traffic areas and away from 

furniture  and  draperies.    Clothing  or  other  flammable  material  should  not  be  placed  on  or  near  the 

appliance.  Children and adults should be alerted to the hazards of high surface temperatures and should 

stay  away  to  avoid  burns  or  clothing  ignition.    Children  should  not  be  left  unsupervised  in  the  room 

when this appliance is in operation.

If any part of this appliance has been exposed to water, DO NOT USE it!!  Immediately call a qualified 

service  technician  to  inspect  the  appliance,  and  to  replace  any  part  of  the  control  system  or  any  gas 

control which has been under water.

This appliance should NOT be modified under any circumstances.  Any parts removed for servicing must 

be replaced before operating this appliance.  Installation and repair should only be done by a qualified service 

technician.  The appliance and its venting system should be inspected and cleaned annually by a qualified 

service technician.  More frequent cleaning may be necessary due to excess lint and dust from carpeting, 

bedding material, etc.  Be sure to turn off gas valve and pilot before cleaning this appliance.

Install at least one smoke detector on each floor of your home to ensure your safety.  They should be located 

away from the gas appliance and close to the sleeping areas.  Follow the smoke detector manufacturer’s 

placement and installation instructions, and be sure to maintain regularly.  Your local fire department may 

provide assistance in selecting smoke detectors, or contact the Consumer Product Safety Commission, 

Washington, D.C. 20207.

WARNING:  

Do not operate appliance with the glass front removed, cracked or broken.  Replacement of 

the glass should be done by a licensed or qualified service person.

Summary of Contents for GRAND BAY 40 GB40FS





































Reviews: