Quadra-Fire 7100FP-GD-B Owner'S Manual Download Page 6

Page: 6 / 36

The Quadra-Fire 7100FP meets the 2015 US Enviornmen

tal Protection Agency’s crib wood emission limits for wood

heaters sold after May 15, 2015.

Model:

7100FP

Laboratory:

OMNI Test Laboratories, Inc.

Report No:

061-S-41-2

Type:

Wood Fireplace

Standard:

UL 127 and ULC S610-M87 and
(UM) 84-HUD, Manufactured
Home Approved.

•  Installation and use of any damaged appliance.
•  Modification of the appliance.
•  Installation  other  than  as  instructed  by  Hearth  &  Home

Technologies.

• Installation and/or use of any component part not approved by

Hearth & Home Technologies.

• Operating appliance without fully assembling all components.
• Do NOT Overfire - If appliance or chimney connector glows,

you are overfiring.

Any such action that may cause a fire hazard.

Listing and Code Approvals

A. Appliance Certification

NOTE: Hearth & Home Technologies, manufacturer of

this appliance, reserves the right to alter its products, their

specifications and/or price without notice.

C. Mobile Home Approved

•

This appliance is approved for mobile home installa

tions when not installed in a sleeping room and when

an outside combustion air inlet is provided.

•

The structural integrity of the mobile home floor, ceil

ing, and walls must be maintained.

•

The appliance must be properly grounded to the frame

of the mobile home with #8 copper ground wire.

•

Outside Air Kit must be installed in a mobile home in

stallation.

Improper installation, adjustment, alteration, service or

maintenance can cause injury or property damage.

For assistance or additional information, consult a qualified

installer, service agency or your dealer.

Quadra-Fire is a registered trademark of Hearth & Home

Technologies.

WARNING

Fire Risk.

Hearth & Home Technologies disclaims any

responsibility for, and the warranty will be voided by,

the following actions:

B. BTU & Efficiency Specifications

D. Glass Specifications

This fireplace is equipped with 5mm ceramic glass. Replace

glass only with 5mm ceramic glass. Please contact your

dealer for replacement glass.

This wood heater needs periodic inspection and repair for

proper operation. It is against federal regulations to operate

this wood heater in a manner inconsistent with operating

instructions in this manual.

EPA Certification #: 571 4-1-03

EPA Certified Emissions: 3.1 grams per hour

*LHV Tested Efficiency: 77.6 %

**HHV Tested Efficiency: 71.8%

***EPA BTU Output: 12,100 to 58,800 / hr.

****Peak BTU/Hour Output: 92,400

Vent Size: 8 inches

Firebox Size: 3.4 cubic feet

Recommended Log Length: 24 inches

Fuel

Seasoned Cord Wood

* * Weighted average LHV (Low Heating Value) efficiency using

Douglas Fir dimensional lumber and data collected during EPA

emission test. LHV assumes the moisture is already in a vapor

state so there is no loss in energy to vaporize.

****

Weighted average HHV (High Heating Value) efficiency using

Douglas Fir dimensional lumber and data collected during EPA

emission test. HHV includes the energy required to vaporize the

water in the fuel.

***

A range of BTU outputs based on EPA Default Efficiency and

the burn rates from the low and high EPA tests, using Douglas

Fir dimensional lumber.

****

A peak BTU out of the appliance calculated using the maxi

mum first hour burn rate from the High EPA Test and the BTU

content of cordwood (8600) times the efficiency.

Quadra-Fire • 7100 FP Owner’s Manual • 433-3600 • Rev J • 09/21/15

►

Summary of Contents for 7100FP-GD-B





































Search results

Summary of Contents for 7100FP-GD-B

Reviews:

Related manuals for 7100FP-GD-B

Brands by name

Popular brands

Quadra-Fire 7100FP-GD-B, Owner'S Manual

Search results

Summary of Contents for 7100FP-GD-B

Reviews:

Related manuals for 7100FP-GD-B

Brands by name

Popular brands