Quadra-Fire 7100FP-BK-B Owner'S Manual Download Page 44

Page: 44 / 72

Page 44

433-1390G

September 1, 2008

7100FP EPA Woodburning Fireplace

Operating Instructions

Do not over-ﬁre.

Over-ﬁring may ignite creosote or will damage
the stove and chimney.

To prevent over-ﬁring your stove, DO NOT:

•  Use ﬂammable liquids
•  Overload with wood
•  Burn trash or large amounts of scrap lumber
•  Permit too much air to the ﬁre

WARNING

Fire Risk

Symptoms of over-ﬁring may include one or more of the
following:

• Chimney connector or appliance glowing

• Roaring, rumbling noises

• Loud cracking or banging sounds

• Metal

warping

• Chimney

ﬁre

1. Symptoms of Over-Firing

2. What To Do if Your Stove is Over-Firing

• Immediately close the door and air controls to reduce

air supply to the ﬁre.

• If you suspect a chimney ﬁre, call the ﬁre department

and evacuate your house.

• Contact your local chimney professional and have your

stove and stove pipe inspected for any damage.

• Do not use your stove until the chimney professional

informs you it is safe to do so.

Hearth & Home Technologies WILL NOT warranty stoves
that exhibit evidence of over-ﬁring. Evidence of over-ﬁring
includes, but is not limited to:

• Warped air tube

• Deteriorated refractory brick retainers

• Deteriorated bafﬂe and other interior components

A. Over-Firing Your Appliance

HOT SURFACES!

Glass and other surfaces are
hot during operation AND
cool down.

WARNING

Hot glass will cause burns.

•  Do not touch glass until it is cooled
• NEVER allow children to touch glass
•  Keep children away
•  CAREFULLY SUPERVISE children in the same room

as appliance

• Alert children and adults to hazards of high

temperatures

High temperatures may ignite clothing or other

ﬂammable materials.

• Keep clothing, furniture, draperies and other

combustibles away.

B. Clear Space Near the Fireplace

Combustible materials must not be stored on the hearth ex-
tension. Room furnishings such as drapes, curtains, chairs
or other combustibles must be at least 4 ft (1219mm) from
the open front of the ﬁreplace.

Summary of Contents for 7100FP-BK-B









































































Search results

Summary of Contents for 7100FP-BK-B

Reviews:

Related manuals for 7100FP-BK-B

Brands by name

Popular brands

Quadra-Fire 7100FP-BK-B, Owner'S Manual

Search results

Summary of Contents for 7100FP-BK-B

Reviews:

Related manuals for 7100FP-BK-B

Brands by name

Popular brands